BEINAT SGM600 Скачать руководство пользователя страница 7

Page  7

Gas  imput  Test

WARNING! Actions to be taken in case of alarm

Gas
1) P
ut out all free flames.
2) Close the main gas tap or the LPG cylinder tap.
3) Do not turn any lights on or off; do not turn on any electrical device or appliance.
4) Open windows and doors in order to increase ventilation.
If the alarm stops, its cause must be found and the relevant consequent measures taken.
If the alarm continues and the cause of gas presence cannot be found or removed, abandon the building and call
the emergency services when outside (fire department, distributors, etc.)

IMPORTANT:  The  operation  test  should  not  be  carried  out  with  the  gas  tap  as  this  does  not  guarantee  a  sufficient
concentration  to  activate  the  general  alarm.

Warning !!

If you have the following symptoms: vomiting, sleepiness, or else, go to the closest first aid station
and inform the operators that you could have been poisoned by Carbon Monoxide

or by an excess

or  deficiency  of  oxygen

N O T E S

The  installation  of  the  SGM600  probe,  its  ordinary  and
extraordinary maintenance, and its out of service removal at
the end of the functional life guaranteed by the manufacturer,
must be carried out by authorized or specialized personnel.

The general test should be performed by issuing gas from a pre-
calibrated  aerosol within the  percentages  illustrated on the
side.

Important: 

This test must be carried out at least once a year.

Gas

TEST  SGM600

with  pre  calibrated  gas  bottle
at  20%  of  LEL    ±2%

            For GAS

Methane
LPG
Hydrogen
Ammonia-explosiv
Acetylene
Gasoline vapors
Alcohol

Содержание SGM600









Отзывы: