Behringer 960 SEQUENTIAL CONTROLLER, Быстрый старт

Страница: 2 / 3

2
960 SEQUENTIAL CONTROLLER Quick Start Guide
3
6. Set the 960 oscillator’s maximum high frequency as follows:
a. Make sure no jack is connected to the CONTROL INPUT.
b. Set the FREQUENCY VERNIER fully clockwise (10 on the scale).
c. Adjust the FREQUENCY ADJUST trimmer to set exactly 500 Hz at the
OSCILLATOR OUTPUT.
d. Apply e2.0 VDC to the CONTROL INPUT jack (this may stop the
oscillator running).
e. Adjust the FREQ STOP ADJ trimmer until the oscillator starts running
and set the maximum frequency to around 550 Hz.
f. Disconnect the +2.0 VDC CONTROL INPUT and check the oscillator
frequency is 500 Hz. Adjust the FREQUENCY ADJUST trimmer if required.
g. Apply e2.0 VDC to the CONTROL INPUT jack, if the oscillator
stays running, the trimming is completed. If not, repeat as required.
Power Connection
The module comes with the required power cable for connecting to a standard
Eurorack power supply system. Follow these steps to connect power to the
module. It is easier to make these connections before the module has been
mounted into a rack case.
1. Turn the power supply or rack case power off and disconnect the power
cable.
2. Insert the 16-pin connector on the power cable into the socket on the
power supply or rack case. The connector has a tab that will align with the
gap in the socket, so it cannot be inserted incorrectly. If the power supply
does not have a keyed socket, be sure to orient pin 1 (-12 V) with the
red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of the module.
The connector has a tab that will align with the socket for
correct orientation.
4. After both ends of the power cable have been securely attached, you may
mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP
apart along the length of the case, or a track that allows individual threaded
plates to slide along the length of the case. The free-moving threaded plates
allow precise positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module before attaching
the screws.
Hold the module against the Eurorack rails so that each of the mounting holes
are aligned with a threaded rail or threaded plate. Attach the screws part way to
start, which will allow small adjustments to the positioning while you get them
all aligned. After the final position has been established, tighten the
screws down.
Specifications
Inputs
Oscillator on/off
Type 2 x 3.5 mm TS jacks, AC coupled
Impedance >3 kΩ, unbalanced
Maximum input level +5 V
Minimum switching threshold +3.5 V trigger
Control input
Type 3.5 mm TS jack, 1 V/oct
Impedance 100 kΩ, unbalanced
Maximum input level ± 2 V, vernier set to 5
Shift input
Type 3.5 mm TS jack, DC coupled
Impedance 7 kΩ, unbalanced
Maximum input level ± 5 V
Minimum switching threshold +1.5 V
Stage triggers
Type 8 x 3.5 mm TS jacks, AC coupled
Impedance >3 kΩ, unbalanced
Maximum input level +5 V
Minimum switching threshold +3.5 V trigger
Outputs
Row outputs
Type 6 x 3.5 mm TS jacks, DC coupled
Impedance 500 Ω, unbalanced
Maximum output level +8 V (range X4)
Stage trigger outputs
Type 8 x 3.5 mm TS jacks, DC coupled
Impedance 250 Ω, unbalanced
Maximum output level +5 V, active high
Oscillator output
Type 3.5 mm TS jack, DC coupled
Impedance 4 kΩ, unbalanced
Maximum output level +4 dBu
Duty cycle 90%
Controls
Frequency range
1 (0.04 to 0.5 Hz), 2 (2.75 to 30 Hz)
3 (0.17 to 2 Hz), 4 (11 to 130 Hz)
5 (0.7 to 8 Hz), 6 (44 to 500 Hz)
Frequency vernier Tune the oscillator range, 3 octave range
Oscillator on/off Manually start or stop the oscillator
Voltage knobs -∞ to max voltage set by the range switch
Mode switch Skip stage, play stage, stop sequencer
Set Manually select stage
Range switches X1 (+2 V), X2 (+4 V), X4 (+8 V) max. output
Timing on/off
Allows 3rd row knobs to control
stage duration
Shift button Manually skip to next stage
Power
Power supply Eurorack
Current draw 100 mA (+12 V), 50 mA (-12 V)
Physical
Dimensions 284 x 129 x 47 mm (11.2 x 5.1 x 1.9")
Rack units 56 HP
Weight 0.64 kg (1.41 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specifications, appearances and other
information are subject to change without notice. All trademarks are the property
of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy,
Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio
are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music
Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online at
musictribe.com/warranty.