manualshive.com logo in svg

BEHR S5, Руководство по эксплуатации, Страница: 16 / 38

Поделиться
Скачать
BEHR S5 Скачать руководство пользователя страница 16

– 16 –

behr S 5

249101

Explanation:

Prog.Number 01

You can modify the settings of pro-

gram no. 01

REAC.TIME

Delay time in seconds between 

the end of NaOH addition and the 

start of distillation. Possible entry 

values range from 0 sec to 999 

sec. The factory default setting 

is 0 sec. For the distillation in the 

Kjeldahl nitrogen determination, 

do not change the preset default 

of 000.

POWER

Steam generator power. Possible 

entry values range from 30% to 

100%. The factory preset default 

value is 80%. You can change the 

electrical power for steam gene-

ration and thereby the intensity of 

steam generation.
The steam generator is swit-

ched on and off on by a pressure 

sensor. The on/off set points of 

the pressure sensor cannot be 

adjusted by the user. It is only 

possible for the user to adjust the 

steam generation power.

DRAINSAMPLE

Run-time in seconds for the pump 

draining the sample waste after 

distillation. Possible entry values 

range from 0 sec to 999 sec. The 

factory default setting is 30 sec.

<<==

back

==>>

further

If you wish to change any of the values, select the 

desired parameter by turning the operating control knob. 

Press on the control knob to access the numerical entry 

value. Then dial the desired value by turning the oper-

ating control knob and enter it in memory storage by 

pressing the knob again.
Once all entry values have been entered according to 

your wishes, select 

==>>

 and press the operating con-

trol knob to bring up the following program menu:

DrainTitr

010

H3BO3

3.0

AutoEndPt

Off

==>>

<<==

Prog.Number

01

Explanation:

AutoEndPt

Automatic endpoint determination. 

Before destillation, the S 5 deter-

mines the pH of the boric acid; 

afterwards it titrates back to this 

pH. If AutoEndPt is Off, titration 

goes to a fixed endpoint. Not all 

titrators allow automatic endpoint 

determination!

DrainTitr

Run-time in seconds for the pump 

draining the distillate after titration. 

Possible entry values range from 

0 sec to 999 sec. The factory  

default setting is 30 sec.

H3BO3

Delivery time for boric acid into the 

titration vessel in seconds.  

Possible entry values range from 

0.0 sec to 99.9 sec. The factory 

default setting is 3.0 sec.
Delivery of the pump approx. 

14 ml/sec. 

70 ml/5 sec 

840 ml/min

<<==

back

==>>

further

If you wish to change any of the values, select the 

desired parameter by turning the operating control knob. 

Press on the control knob to access the numerical entry 

value. Then dial the desired value by turning the oper-

ating control knob and enter it in memory storage by 

pressing the knob again.

Once all entry values have been entered according to 

your wishes, select 

==>>

 and press the operating con-

trol knob to bring up the following program menu:

Meas.Time

020

Stirring

40%

SetPoint

4.6

<<==

Prog.Number

01

Explanation:

SetPoint

Endpoint preset for the titra-

tion. Titration will go to this pH if  

AutoEndPt is off.  

Not all titrators allow endpoint 

setting from the S 5. With some 

titrators the endpoint must be set 

on the titrator itself.

Meas.Time

Time in seconds for the endpoint 

determination if AutoEndPt is on 

and the titrator allows automatic 

endpoint determination. The fac-

tory default setting is 10 sec.

Distilling

Содержание S5







































Отзывы:

Нет отзывов