Bedrock UPS.500 Скачать руководство пользователя

Страница: 50 / 54

Appendix C

C-1

Bedrock UPS.500 User Manual - BRDOC120_008

9/2/21

Certifications, Approvals, and Testing

The Bedrock UPS.500 has received the following certifications and approvals:

CE Testing

European EMC Directive 2014/30/EU including:

• CISPR 11: 2010 Radiated Emissions

• IEC 61000-4-3 Radiated RF Immunity

IEC Environmental

Testing

The Bedrock UPS.500 meets the following environmental specifications:

• Shock (Operating) - IEC 60068-2-27

• Shock (Non-Operating) - IEC 60068-2-27

• Vibration (sinusoidal) - IEC 60068-2-6

• Temperature Code T4 Classification

Underwriters

Laboratories (UL)

Safety Compliance

The Bedrock UPS.500 has received UL approval for use in a Class I Division 2

hazardous location in accordance with the following documents:

• UL 121201 Edition 9, Nonincendive Electrical Equipment for Use in

Class I and II, Division 2 and Class III, Divisions 1 and 2 Hazardous
(Classified) Locations.

• CSA C22.2 No. 213-17, Nonincendive Electrical Equipment for Use

in Class I and II, Division 2 and Class III, Divisions 1 and 2
Hazardous (Classified) Locations, Edition 3.

FCC Testing

The Bedrock UPS.500 has passed testing that demonstrates compliance with the

following Federal Communications Commission (FCC) standard:

• Code of Federal Regulation (CFR) FCC Part 15 Subpart B, Class A

(2016) (Radiated Emissions and AC Mains Conducted Emissions)

EMP Testing

The Bedrock UPS.500 has passed testing that demonstrates that the power supply

is able to withstand transient electromagnetic fields under the following

requirement:

• MIL-STD-461E, Requirements for the Control of Electromagnetic

Interference Characteristics of Subsystems and Equipment —

Содержание UPS.500























































Результаты поиска

Содержание UPS.500

Отзывы:

Похожие инструкции для UPS.500

Бренды по названию

Популярные бренды

Bedrock UPS.500, Руководство пользователя

Результаты поиска

Содержание UPS.500

Отзывы:

Похожие инструкции для UPS.500

Бренды по названию

Популярные бренды