Becx Machines OBKS50-35 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 25

Becx Machines OBKS50-35 Скачать руководство пользователя страница 18

Weed brush

–

Edge cutter

OBKS50-35

Version: 1

November ’19

Page 18 of 25

5.

Maintenance

•

Only components supplied or approved by the manufacturer must be used for
replacement or repair of parts.

•

Always disconnect the weed brush from the feed line when work is carried out
on the machinery. This is done by disconnecting the rapid attachment.

•

Only persons who can show that they have adequate knowledge of
mechanical and hydraulic machinery through their training and experience are
allowed to carry out maintenance work.

•

The installation can be cleansed with a high pressure cleanser, never point
directly at hydraulic components.

Weekly maintenance

No.

What to do

Action

Result

1

Grease the pivot
points

•

Squeeze grease into the grease nipples. These are located
at all pivot points

•

Apply correct spray on the side-shift mechanism.

•

See chapter 1 for grease/spray specifications

2

Tightening bolts

•

Check and tighten all bolts

3

Visual check

•

Visually check the construction, the hydraulic aggregate
and the cutter blades for damage and cracks.

•

Check cylinder-rods for damages and dirt.

4

Retighten
adjusting bolts

•

Within 4 working hours, tighten the set screws of the
clamping sleeve mounting on the motor shaft and then
check it regularly! (48 NM) See image on page 19.

SMEERPUNTEN

«
...
16
17
18
19
20
...
»

Содержание OBKS50-35


























Отзывы:

Нет отзывов