background image

Overview

PS3031-2440-0000

5

Version: 1.0

1

Overview

PS3031-2440-0000 | Power supply 24 V, 40 A, 3-phase

• 3AC 380-480 V wide-range input

• Three built-in input fuses

• 95.3% full load and excellent part-load efficiencies

• Width only 110 mm, weight only 1.5 kg

• 150% peak power, 1440 W for up to 4 s

• 110 A peak current over 25 ms for triggering fuses

• Active power factor correction (PFC)

• Active filtering of input transients

• Negligible input inrush current surge

• Full power between -25°C and +60°C

• Option of current sharing for parallel connection

• Controllable output voltage level

• DC-OK relay contact

• Shutdown input

The PS3031-2440-0000 is a 3-phase 24 V power supply with an output current of 40 A and an output power
of 960 W/1440 W.

On the input side, the device features a wide-range input, active power factor correction (PFC) and inrush
current limiting.

The PS3031-2440-0000 features an Extra Power output with a maximum output power of 150% over
4 seconds and is able to trigger fuses precisely with a short-term peak current. The output voltage can be
switched off by means of the shutdown contact. A DC-OK LED, an overload LED and a potential-free relay
contact monitor the status of the output voltage.

The power supply is part of the PS3000 family and has a width of 110 mm.

Overview of technical data 

*)

Overview of technical data

PS3031-2440-0000

Output voltage

DC 24 V (nominal)

Adjustment range

24 - 28 V

Output current

40 - 34.3 A (continuous); 60 - 51.5 A (short-term for 4 s)

Output power

960 W (continuous); 1440 W (short-term for 4 s)

Output ripple

< 100 mVpp (20 Hz to 20 MHz)

Input voltage AC

3AC 380-480 V -15%/+20%

Mains frequency

50-60 Hz ±6%

Input current AC

1.65 / 1.35 A at 3 x 400 / 480 Vac

Power factor

0.88 / 0.90 at 3 x 400 / 480 Vac

Inrush current surge AC

typ. 4.5 A peak

Efficiency

95.3 / 95.2% at 3 x 400 / 480 Vac

Losses

47.3 / 48.4 W at 3 x 400 / 480 Vac

Operating temperature range

-25°C to +70°C

Derating

24 W / °C (+60°C to +70°C)

Hold-up time

Typ. 25 / 25 ms at 3 x400 / 480 Vac

Dimensions (W x H x D)

110 x 124 x 127 mm (without DIN rail)

Weight

1500 g

Approvals/markings

CE, cULus, EAC

*) All values typical for 24 V, 40 A, 3x 400 Vac, 25°C ambient temperature and after a warm-up time of 5 minutes, unless otherwise
stated.

Содержание PS3031-2440-0000













































Отзывы: