background image

Product overview

ELX4154

14

Version: 1.0

Technical data for explosion protection

ELX4154-0000

Ex marking

II 3 (1) G Ex ec [ia Ga] IIC T4 Gc

II (1) D [Ex ia Da] IIIC

I (M1) [Ex ia Ma] I

Certificate numbers

IECEx BVS 18.0005X

BVS 18 ATEX E 005 X

Power supply

Invariable in connection with ELX9560

Field interfaces

UO = 27.7 V
IO = 85 mA
PO = 565 mW
Characteristic curve: linear

Reactance (without consideration
of the simultaneousness)

L

0

C

0

Ex ia I

43 mH

3.45 µF

Ex ia IIA

30 mH

2.2 µF

Ex ia IIB

18 mH

663 nF

Ex ia IIC

2 mH

85 nF

Ex ia IIIC

18 mH

663 nF

2.3

Intended use

 WARNING

Endangering the safety of persons and equipment!

The ELX components may only be used for the purposes described below!

 CAUTION

Observe ATEX and IECEx!

The ELX components may only be used in accordance with the ATEX directive and the IECEx scheme!

The ELX terminals extend the field of application of the Beckhoff bus terminal system with functions for
integrating intrinsically safe field devices from hazardous areas. The intended field of application is data
acquisition and control tasks in discrete and process engineering automation, taking into account explosion
protection requirements.

The ELX terminals are protected by the type of protection "Increased safety" (Ex e) according to
IEC 60079-7 and must only be operated in hazardous areas of Zone 2 or in non-hazardous areas.

The field interfaces of the ELX terminals achieve explosion protection through the type of protection "intrinsic
safety" (Ex i) according to IEC 60079-11. For this reason, only appropriately certified, intrinsically safe
devices may be connected to the ELX terminals. Observe the maximum permissible connection values for
voltages, currents and reactances. Any infringement can damage the ELX terminals and thus eliminate the
explosion protection.

The ELX terminals are open, electrical equipment for installation in lockable cabinets, enclosures or
operating rooms. Make sure that access to the equipment is only possible for authorized personnel.

 CAUTION

Ensure traceability!

The buyer has to ensure the traceability of the device via the Beckhoff Traceability Number (BTN).

Содержание ELX1052-0000-0001


































Отзывы: