Beckhoff CX8190 Скачать руководство пользователя страница 63

Страница: 63 / 72

Care and maintenance

CX8190

Version: 1.5

Care and maintenance

10.1

Replace the battery

NOTE

Risk of explosion

An incorrectly inserted battery may explode and damage the Embedded PC.

Only use original batteries and ensure that the positive and negative poles are inserted correctly.

The battery must be replaced every 5 years. Spare batteries can be ordered from Beckhoff Service. A
battery of type CR2032 is used for the Embedded PC.

Table 19: Technical data of the battery.

Battery type

Electrical properties (at

20 °C)

Standard

load

Dimensions

nominal volt-

age

nominal

capacity

continuous

load

Diameter

Height

CR2032

3.0 V

225 mAh

0.20 mA

20.0 mm

3.20 mm

The battery compartment is below the front flap. The battery stores the time and date. The time and date are
reset if the battery is removed.

Be aware of this behavior for your hardware and software configuration and reset the time and date after a
battery change.

Requirements:

• The Embedded PC is switched off.

Replace the battery as follows:

1. Open the front flap.

2. Apply the screwdriver below or above the battery and prize the battery carefully out of the battery

compartment.

CX8190

3. Push the new battery into the battery compartment. The plus pole points to the left towards the Ethernet

interfaces.

CX8190

The battery change is complete. Close the front flap and reset the date and time.

Содержание CX8190









































































Результаты поиска

Содержание CX8190

Отзывы:

Похожие инструкции для CX8190

Бренды по названию

Популярные бренды

Beckhoff CX8190, Руководство пользователя

Результаты поиска

Содержание CX8190

Отзывы:

Похожие инструкции для CX8190

Бренды по названию

Популярные бренды