Beckhoff CU8130-0240 страница 49 Скачать руководство пользователя | Manualshive

Страница: 49 / 57

background image

Decommissioning

CU8130-0240

49

Version: 1.1

10.2

Disposal

Beckhoff Automation products are marketed exclusively to corporate customers. According to the directive
2012/19/EU "WEEE", we take old devices and accessories back for professional disposal. The transport
costs are covered by the sender.

Send the old devices with the note "For disposal" to:

Beckhoff Automation GmbH & Co. KG
Gebäude „Service“
Stahlstraße 31
D-33415 Verl

Replacement battery modules

CU9900-U015 and CU9900-U030 replacement battery modules for CU8130 UPS modules from Beckhoff
Automation GmbH & Co. KG are marketed exclusively to corporate customers. According to the German law
on batteries (BattG), we take old batteries back and pass them on to a disposal company. The transport
costs are covered by the sender.

Send the old battery with the note "For disposal" to:

Beckhoff Automation GmbH & Co. KG
Building "Service“
Stahlstraße 31
D-33415 Verl

The packaging of the replacement battery can be used to return the old battery.

«
...
47
48
49
50
51
...
»

Содержание CU8130-0240


























































Отзывы:

Нет отзывов

Похожие инструкции для CU8130-0240

Бренд: UHV Design Страницы: 56

Бренд: ?HC Страницы: 2

Бренд: tacwise Страницы: 5

PFE300SA Series

Бренд: TDK-Lambda Страницы: 19

Бренд: Status Страницы: 22

Бренд: M-system Страницы: 3

Бренд: Ransburg Страницы: 40

Бренд: Omer Страницы: 26

Бренд: Valcom Страницы: 3

ProJet Cart Station

Бренд: 3D Systems Страницы: 21

Бренд: X-Tronic Страницы: 12

Бренд: Worldwide Страницы: 2

Бренд: Unimac Страницы: 15

Бренд: Yamato Страницы: 12

Бренд: Emerald Planet Страницы: 3

EVS 30/20-DS/IU

Бренд: Calira Страницы: 64

Бренд: Senco Страницы: 2

Бренд: tekton Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды