background image

 

General instructions 

 

General instructions 

 

Notes on the Documentation 

 

This description is only intended for the use of trained specialists in control 
and automation engineering who are familiar with the applicable national 
standards. It is essential that the following notes and explanations are 
followed when installing and commissioning these components. 
 

 

Liability Conditions 

 

The responsible staff must ensure that the application or use of the 
products described satisfy all the requirements for safety, including all the 
relevant laws, regulations, guidelines and standards. 

The documentation has been prepared with care. The products described 
are, however, constantly under development. For that reason the 
documentation is not in every case checked for consistency with 
performance data, standards or other characteristics. None of the 
statements of this manual represents a guarantee (Garantie) in the 
meaning of § 443 BGB of the German Civil Code or a statement about the 
contractually expected fitness for a particular purpose in the meaning of 
§ 434 par. 1 sentence 1 BGB. In the event that it contains technical or 
editorial errors, we retain the right to make alterations at any time and 
without warning. No claims for the modification of products that have 
already been supplied may be made on the basis of the data, diagrams 
and descriptions in this documentation. 

© This documentation is copyrighted. Any reproduction or third party use of 
this publication, whether in whole or in part, without the written permission 
of Beckhoff Automation GmbH, is forbidden. 
 

 

Description of safety symbols 

 

The following safety symbols are used in this operating manual. They are 
intended to alert the reader to the associated safety instructions. 
 

 

Danger

 

 

This symbol is intended to highlight risks for the life or health of personnel. 

 

 

 

 

Warning

 

 

This symbol is intended to highlight risks for equipment, materials or the 
environment. 

 

 

 

i

 

Note

 

 

This symbol indicates information that contributes to better understanding. 

 

 

C63xx  

StockCheck.com

Содержание C63 Series



































Отзывы: