Beckhoff AG3300 Скачать руководство пользователя страница 61

Страница: 61 / 68

Maintenance and cleaning

Version: 2.5

───

AG3300

10.2

Intervals

Under nominal conditions, the motor components have different op-
erating hours. We have provided you with a list of maintenance work
and intervals for the associated components below:

Component

Interval

Maintenance

Gear unit

During commission-
ing

Thereafter:

Every three months

Check gear unit for external damage and leaks

Check drive shaft and output shaft for foreign media such as oil
and dirt

Check gear unit for corrosion

Clamping screw
Motor attachment

During commission-
ing

Thereafter:

Every three months

Check tightening torques

Fastening screw
Gear unit housing

During commission-
ing

Thereafter:

Every three months

Check tightening torques

10.2.1

Lubrication

Notes on lubrication

Beckhoff gear units from the AG3300 series are lubricated for life.
The lubricant used does not have to be renewed.

If you wish to change the lubricant, contact Beckhoff Service.

All gear units are lubricated for life in the factory with a synthetic
polyglycol gear oil or with a high-performance grease.

Refer to the name plate for detailed information on lubrication. All
bearings are lubricated for life at the factory.

Further information on the lubricants can be obtained directly from
the manufacturer.

Содержание AG3300





































































Результаты поиска

Содержание AG3300

Отзывы:

Похожие инструкции для AG3300

Бренды по названию

Популярные бренды

Beckhoff AG3300, Руководство по эксплуатации

Результаты поиска

Содержание AG3300

Отзывы:

Похожие инструкции для AG3300

Бренды по названию

Популярные бренды