Beckhoff AG2250 страница 22 Скачать руководство пользователя

Страница: 22 / 95

Technical data

───

Version: 2.8

AG2250

Below you will find definitions of terms, environmental conditions,
operating details and technical data for the planetary gear units.

4.1

Definitions

When attaching a gear unit, the performance may be reduced by up
to 20 %. The flange of a motor serves to dissipate heat. If a gear
unit is attached, heat is generated due to operation. The power der-
ating therefore has thermal reasons.

4.1.1

Technical terms

This chapter provides information on various technical terms and
their meaning.

Equivalent force on the output F

2_eq

[N]

The equivalent force on the output describes the force that is rele-
vant for dimensioning the gear unit.

Equivalent application torque T

2_eq

[Nm]

The equivalent application torque describes the torque that is rele-
vant for the dimensioning of the gear unit.

Dimensioning factor f

The dimensioning factor describes the influence of the daily operat-
ing time and the operating factor on the application torque.

Operating mode factor K

The operating mode factor describes the influence of duty cycle,
number of cycles and dynamics on the application torque.

Mass moment of inertia; based on the drive J

[kgcm²]

The mass moment of inertia is a measure for the tendency of a body
to maintain its motion state (whether at rest or in motion).

Running noise Q

[dB/A]

The running noises are influenced, for example, by:

• transmission ratio and speed

• lubricants and gearing or

• Installation position

Содержание AG2250
































































































Результаты поиска

Содержание AG2250

Отзывы:

Похожие инструкции для AG2250

Бренды по названию

Популярные бренды

Beckhoff AG2250, Руководство по эксплуатации

Результаты поиска

Содержание AG2250

Отзывы:

Похожие инструкции для AG2250

Бренды по названию

Популярные бренды