background image

  Rev: April 2015 

6 of 18 

® 

  BEAST    Electric Pressure Washers 

The high pressure stream of water that this equipment produces 
can pierce skin and its underlying tissues, leading to serious 
injury and possible amputation. 

Spray gun traps high water pressure, even when pump is not 
running and water is disconnected, which can cause injury. 



NEVER aim spray gun at people, animals, plants, electrical devices, 
or the unit itself. 



DO NOT allow children to operate pressure washer. 



To reduce the risk of injury, do not operate the machine near 
children 



NEVER repair high pressure hose. Replace it. 



NEVER repair leaking connections with sealant of any kind.  
Replace o-ring or seal. 



Keep high pressure hose connected to pump and spray gun while 
system is pressurized. 



ALWAYS point gun in safe direction and squeeze spray gun trigger, 
to release high pressure, every time you stop engine.  Engage 
trigger lock when not in use.

 

WARNING 

High pressure spray can cause paint chips or other particles to 
become airborne. 



Always wear eye protection when using this equipment or in 
vicinity of where equipment is in use. 

WARNING 

  Risk of Electrocution 



Inspect cord before using - Do not use if cord is damaged. 



Keep all connections dry and off the ground. 



Do not touch plug with wet hands. 



If possible, do not use extension cords with the product. 



Water spray must never be directed towards any electric wiring, 
electrical devices, or toward the unit itself. 

WARNINGS 

Extension Cords 

If possible, do not use extension cords with this 
product. However, if you must use one, observe all 
the warnings and instructions listed below: Use a sufficient gauge: 



Maximum cable length: 50 ft = 14 AWG 



Use only extension cords that are intended for outdoor use. These 
extension cords are identified by a marking “Acceptable for use 
with outdoor appliances; store indoors while not in use.” 



Use only extension cords having an electrical rating not less than 
the rating of the product.  



Do not use damaged extension cords. Examine extension cord 
before using and replace if damaged.  



Do not abuse extension cord and do not yank on any cord to 
disconnect. 



Keep cord away from heat and sharp edges. 



Always disconnect the extension cord from the receptacle before 
disconnecting the product from the extension cord.  



To reduce the risk of electrocution, keep all connections dry and off 
the ground. Do not touch plug with wet hands. 

 

WARNING 

The pressure washer is also equipped with a main power “ON/OFF” 
switch located on the unit. It should always be moved to the “OFF” 
position when the pressure washer is not being used to prevent possible 
injury or damage. 

CAUTION 

A pressure washer produces a high pressure spray which 
increases risk of injury and damage to unit. 



Gun Kicks Back - Hold with both hands! 



The trigger gun safety lock prevents the trigger from accidentally 
being engaged. The safety feature DOES NOT lock trigger in the ON 
position. 



DO NOT secure spray gun in open position. 



DO NOT leave spray gun unattended while machine is running. 



NEVER use a spray gun which does not have a trigger lock or 
trigger guard in place and in working order. 



Always be certain spray gun, nozzles and accessories are correctly 
attached. 

High pressure spray may damage fragile items including glass. 



DO NOT point spray gun at glass when in jet spray mode. 



NEVER aim spray gun at people, animals, plants, electrical devices, 
or the unit itself. 

CAUTION 

  Risk of Explosion 



DO NOT spray flammable liquids 



DO NOT use acids and solvents in this product.  These products can 
cause physical injuries to the operator and irreversible damage to 
the machine. 

Improper treatment of the pressure washer can damage it and 
shorten its life. 



If you have questions about intended use, ask dealer or  contact 
Customer Service at [1] 919-550-3221. 



NEVER operate units with broken or missing parts, or without 
protective housing or covers. 



DO NOT bypass any safety device on this machine. 



Before starting pressure washer in cold weather, check all parts of 
the equipment to be sure ice has not formed there. 



NEVER move machine by pulling on high pressure hose. Use handle 
provided on unit. 



This equipment is designed to be used with BEAST authorized parts 

ONLY

. If equipment is used with parts that DO NOT comply with 

minimum specifications, user assumes all risks and liabilities. 

CAUTION 

Содержание P1450B



















Отзывы: