background image

4

Page 4 of 4  

75.5996.03 MS41 20210421

BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, 
Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and 
factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/
device system performance is compliant with local, national, and international regulations, codes, and standards. 
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations 
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices.  Safety inspections must be performed during each service 
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, 
UL325, and International Building Code). 
Verify that all appropriate industry signage, warning labels, and placards are in place. 

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

Tech Support & Customer Service: 1-800-523-2462

General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com

Door does not open when 
swiping hand in front of 
sensor

Bad or no power

Check power supply, ensure SELV-
equivalent power.  If LED switches on or 
flashes, power connections are okay.

Detection range too short

Adjust detection zone.  Remove any metal 
plates in front of sensor.

Incorrect wiring/connection

Check wiring and relay connection.

Sensor stays in detection

Environmental conditions 
influencing sensor

Remove moving objects from around 
sensor.

Wrong output mode

Switch output mode to Timer.

Door remains open after 
detection/activation

Wrong output mode

Switch output mode to Timer.

Incorrect wiring/connection

Check wiring and relay connection.

©BEA

 | Original Instructions | PLEASE KEEP FOR FUR

THER USE - DESIGNED FOR COLOR PRINTING

FCC APPROVAL

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:

*this device may not cause harmful interference, and
*this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

*Reorient or relocate the receiving antenna
*Increase the separation between the equipment and receiver
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
*Consult the dealer or an experienced radion/TV technician for help

WARNING: CHANGES OR MODIFICATIONS TO THIS EQUIPMENT NOT EXPRESSLY APPROVED BY BEA INC. MAY VOID THE FCC 
AUTHORIZATION TO OPERATE THIS EQUIPMENT.

INSTALLATION

1. Install an electrical box.  

If using a metal eletrical box, ensure that the 

sensor and related wiring does not come in 

contact with the box to avoid shorting the unit.

2. Clip the MS41 cube to the face plate. 

I

f IP65 rating is desired, apply silicone between the MS41 

cube and face plate prior to installing the MS41 onto 
electrical box.

3. Secure the face plate to the electrical box with the 

provided screws.

electrical box

(

metal/plastic

)

MS41

assembly

TROUBLESHOOTING

Содержание MS41

Страница 1: ...adapter bracket 2 Not provided by BEA 6 ROUND TECHNICAL SPECIFICATIONS Technology microwave motion sensor Radiated frequency 24 125 GHz Radiated power density 5 mW cm2 Supply voltage to be operated from SELV compatible power supplies only 12 24 VAC 10 12 24 VDC 30 10 Supply frequency 50 60 Hz Power consumption 1 5W Output relay contact rating max voltage relay contact rating max current Max switch...

Страница 2: ...e plate on either the top or bottom Only two snap fittings must be loosened empty N C N O COM 12 24 VAC VDC 12 24 VAC VDC PRECAUTIONS Shut off all power going to header before attempting any wiring procedures Maintain a clean and safe environment when working in public areas Constantly be aware of pedestrian traffic around the door area Always stop pedestrian traffic through the doorway when perfo...

Страница 3: ...ty potentiometer adjust detection field from 4 to 24 inches rotate clockwise to increase 5 6 2 3 4 DIP1 DIP2 DIP3 DETECTION NO DETECTION blue off off blue blue blue green off off green green green blue green green blue 1 RETROFIT APPLICATION You can retrofit hardwired push plates using the 900 MHZ Touchless Retrofit Transmitter 10TD900TR and Receiver 10RD900 1 Locate existing 2 wires previously us...

Страница 4: ...ctivation Wrong output mode Switch output mode to Timer Incorrect wiring connection Check wiring and relay connection BEA Original Instructions PLEASE KEEP FOR FURTHER USE DESIGNED FOR COLOR PRINTING FCC APPROVAL This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions this device may not cause harmful interference ...

Отзывы: