BEA FALCON DR Скачать руководство пользователя страница 1

75.5268.01 20070111 

 

Page 1 of 7

 

 

 

FALCON DR  / FALCON XL-DR

 

USER’S GUIDE

 

 

MOTION SENSORS FOR INDUSTRIAL DOORS 

FALCON DR: 

double relay / high mount

  

  FALCON XL-DR: 

double relay / low mount

 

 

Technology                     

:  Microwave and 

microprocessor 

Transmitter frequency    

:  24.125 GHz 

Transmitter radiated power  :  <20 dBm EIRP 

Transmitter power density 

:  < 5 mW/cm² 

Mounting height   

   

 

FALCON DR 

:  from 11.5’ (3.5m) to 23’ (7m)  

 

FALCON XL-DR 

:  from 6.5’ (2m) to 11.5’ (3.5m) 

Tilt angles 

:  0° to 180° in elevation 

Detection zone 

 FALCON DR 

(mounting height of 5m) 

 

13’ (W) x 16’ (D) 

4m (W) x 5m (D) 

 FALCON XL-DR 

(mounting height of 2.5m) 

 

13’ (W) x 6.5’ (D) 

4m (W) x 2m (D) 

Detection mode 

:  Motion 

Minimum speed 

:  2 in (5cm)/s (measured in the 

sensor axis) 

Supply voltage 

:  12V to 24V AC ±10% 

12V to 24V DC +30% / -10% 

Mains frequency 

:  50 to 60 Hz 

Power consumption 

:  < 2W (VA) 

Two Output relay (free of potential change-over contact) 

 

Max. contact voltage 

:  42V AC 

 

Max. contact current 

:  1A (resistive) 

 

Max. switching power 

:  30W (DC) / 60VA (AC) 

 

Hold time 

0.5s to 9s (adjustable) 

Temperature range 

-22°F to +122°F (-30°C to +60°C) 

Degree of protection 

IP65 

Norm conformity 

R&TTE 1999/5/EC 

EMC 89/336/EEC 

Dimensions : 

4” (W) x 5” (D) x 3 ¾” (H) 

 

  102 mm (W) x 127 mm (D) x 96 mm (H) 

Weight : 

0.88 lbs (0.4 kg) 

Material of housing 

ABS and polycarbonate 

Material of bracket 

Anodized aluminium 

Length of cable 

33’ (10m) 

Manual adjustment 

   

 

Orientation of sensing field  (mechanically) 

 

Multiple functions (by push buttons) 

Remote control adjustments 

 

Sensitivity 

 

Hold time 

 

Detection mode 

 

Pedestrian and parallel traffic rejection mode 

 

Output configuration 

 

Security 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 

 
 
 
 

 

 

 
 
 
 
 
 

 

 

 

The sensor must be firmly 
fastened to prevent from 
vibrating.

 

The sensor must not be placed 
directly behind a panel or any kind 
of material.

 

The sensor must not have 
any object likely to move or 
vibrate in its sensing field.

 

The sensor must not have any 
fluorescent lighting in its 
sensing field. 

 
DESCRIPTION OF 
THE SENSOR   

 
INSTALLATION 
TIPS

  

 

 
TECHNICAL 
SPECIFICATION 

Tranceiver module 

(planar antenna) 

 

Green LED 

 

Infrared Receiver 

 

Red LED 

 

 

 

 

 

2 Push Buttons 

 

 

Microprocessor 

 

 

Terminal block 

Содержание FALCON DR








Отзывы: