BE Ag & Industrial 81.200.004 Скачать руководство пользователя страница 9

Страница: 9 / 13

ASSEMBLY INSTRUCTIONS (CONT.)

81.200.004

Step 11: Adjust Handle & Tighten Connections

Place the aerator right side up its wheels, locking the lift handle into the offset at the front of the tray slot.

Perform the following steps to assure correct alignment of the light handle with the slot. Refer to Fig 11.

1. Adjust the tray side to side until the lift handle rests against the right side (viewed from the rear) of the offset

at the front of the slot.

2. Straighten the end plates and then tighten the eight bolts at the corners of the tray, making sure the lift

handle still rests against the right side of the slot offset.

3. Straighten the middle brace and tighten the two bolts which fasten it to the tongue.

Make sure the lift handle still rests against the right side of the slot offset. You should have to force the handle

over into alignment with the slot when lowering the aerator.

The licking device could help to prevent the handle be sliding out when the aerator in running. But if you

feel this device is not convenient, just take out the pin.

Содержание 81.200.004













