manualshive.com logo in svg

BDI STANCE 6650, Руководство пользователя

Поделиться
Скачать
BDI STANCE 6650 Скачать руководство пользователя страница 13

bdiusa.com

[email protected]

STANCE

 

6650/6651/6652

LIFT DESK

13

Height Adjustment

The desk base can be adjusted by pressing and holding either the UP or DOWN button until the desired 

height is reached.

To program up to four presets, use the up/down buttons to find a desired height, then press “

BDI

” followed 

by a number 1-4. To Change the 

Movement Program

 (explained below) follow the 

Reset Procedure

 to 

step 4

.  The display should be flashing “RST”.  Press and hold the “

1

” button (about 5 seconds) until the 

display flashes “10.1” or “10.2”.  You can press and hold the “

1

” button again to switch to the other setting.  

Once the chosen setting is selected finish the Reset Procedure steps 5 and 6.

One Touch (Default) - 10.1: 

Once a preset button is pushed, the desk will move to the programmed height.  To stop movement, press any 

number on the keypad.

Constant Touch - 10.2: 

A preset button must remain pressed for the desk to move to the programmed height.  To stop movement, 

release the button.

Trouble Shooting

If your desk is not functioning properly it may need to be reset. Follow the RESET procedure above.

If your LED readout displays an error message Er1 confirm that all wired connections are secure. Then 

perform the reset procedure above.

Keypad Lock

To lock the keypad:

Press and hold the “

BDI

” button for about 8 seconds until the LED display reads “LOC”.  The keypad is now 

locked and cannot be used to move the desk.

To unlock the keypad:

Press and hold the “

BDI

” button for about 8 seconds until the LED display switches from “LOC” to the height 

display.  The keypad is now unlocked and can be used as normal.

Height Display:  Inches or Centimeters

To change unit of height measurements (inches or centimeters) follow the 

Reset Procedure

 to step 

4

.  The 

display should be flashing “

RST

”.  Press and hold the “

2

” button (about 5 seconds) until the display flashes 

“

10.3

” or “

10.4

”.  You can press and hold the “

2

” button again to switch to the other setting.  Once the chosen 

setting is selected, finish the Reset Procedure steps 5 and 6.

Centimeters - 10.3

Inches (Default) - 10.4

Содержание STANCE 6650
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды