manualshive.com logo in svg

BDI COSMO 5720, Инструкция по эксплуатации

Поделиться
Скачать
BDI COSMO 5720 Скачать руководство пользователя страница 14

14  |  BDIUSA.COM

COSMO 5720

ADJUST DRAWER—IF NEEDED 

CLEANING

3) Pushing the 

orange 

lever 

towards the outside wedges 

the drawer up. Pulling it 

towards the middle of the 

drawer moves the drawer 

down. 

2) Rotating the 

white

 wheel 

towards you moves the 

drawer to the left.  Rotating 

away moves it right. 

1)  Rotating the 

black

 wheel 

towards the inside of the 

drawer moves the drawer 

backward, deeper into the 

cabinet.

Backward

Left

Right

Forward

The drawer on your Cosmo Bar is adjustable as much as 2mm up, down, left, right, back or forward.  
If the drawer is out of alignment, follow the steps below: 

If a spill occurs, the porcelain surface on your Cosmo Bar may be removed for cleaning. To remove, 
open the drawer about 8", reach inside and find the 60mm disc just under the front center edge of the 
porcelain. Rotate the disc 180 degrees. Lift the porcelain out by pushing up from below.

Down

Up

Disc

Rotate Disc to Unlock

Unlocked Position

FINE TUNING

FINE TUNING

Содержание COSMO 5720

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды