background image

3

SAFETY PRECAUTIONS 

Read and follow all safety, operating and maintenance instructions. Failure to read and follow 

these instructions could result in injury or death to you or others. Failure to read and follow these 

instructions could also result in damage and/or reduced equipment life. In order to prevent injury, the 

following safety precautions should be followed at all times! 

READ OWNER'S MANUAL BEFORE USE

Before using this equipment, ensure that the person operating this machine has read and 

understands all of the instructions in the manual. Precaution is the best insurance against accidents. 

Read and understand all safety precautions, messages, warnings and hazard symbols. You are 

responsible for your own safety.

ALWAYS USE SAFETY GLASSES

Safety glasses should always be worn when working around power tools. In addition, a face, dust 

mask or respirator should be worn if a cutting operation is dusty. Everyday eyeglasses only have 

impact resistant lenses and may not prevent eye injury - they are NOT safety glasses.

USE PROPER APPAREL

Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry that may be caught in 

moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. 

Hand protection (plastic gloves) and a shop bib are recommended during sawing to prevent stains 

to clothing. Avoid prolonged exposure of skin to the sawing lubricant and wash skin immediately 

after contact. Do not touch the work material until the motor is off and the machine has come to a 

complete stop.

ALWAYS USE HEARING PROTECTION

To reduce the possibility of hearing loss, always use hearing protection when operating power 

equipment.

KEEP GUARDS IN PLACE

In order to prevent injury, never operate the saw without the guards in place!

REMOVE ADJUSTING KEYS AND WRENCHES

Form a habit of checking to see that keys and adjusting wrenches are removed from the power tool 

before it is turned on.

ELECTRICAL SHOCK

Never touch electrical wires or motor components while the motor is running. Exposed, frayed or 

worn electrical wiring and plugs can be sources of electrical shock that could cause severe injury or 

burns. 

DISCONNECT TOOLS

Power tools should always be disconnected before servicing or when changing accessories, such as 

blades, bits, cutters and the like.

   BD-1272 RAIL SAW  

  

 

 

                                        SAFETY

Содержание BD-1272





































Отзывы: