TO STOP ENGINE
OPERATING HINTS
MAINTENANCE GUIDE
Close the throttle.
Engage clutch lever.
Locate gear lever in neutral position.
Disengage drive to the digging knives.
Release clutch lever.
Release engine stop lever completely.
Turn the ignition key to ‘OFF’ position, and the red light will go out.
WARNING: THE EXHAUST COVER MAY BE HOT - DO NOT
TOUCH
LET THE MACHINE DO THE WORK.
Excessive downward pressure on the handlebars may cause the
machine to jump. Apply gentle pressure and the machine will find its
own digging depth according to the type of ground. If the ground is
hard, position the depth adjuster centre knife on the top hole and
make several passes until the desired depth is achieved.
If the speed or digging knives lever does not engage immediately,
release clutch lever slightly and 'feel in' with the engine on tick-over.
DO NOT ‘RIDE’ THE CLUTCH.
If one wheel begins to lose traction engage the differential lock by
pulling the black lever on top of the right-hand handlebar towards you
to engage drive to both wheels.
Always pull in the clutch lever before engaging any gear, digging unit
or changing forward/reverse.
The clutch lever must be fully released when working. Do not operate
the machine with the clutch lever partially engaged as serious
damage may occur.
DO NOT WORK ON SLOPES MORE THAN 20°
If working on a slope, work across the slope pointing the machine
slightly uphill.
DO NOT ATTEMPT CULTIVATION ON:
(i)
Frozen or waterlogged ground as this will destroy the soil
structure resulting in poor future drainage.
(ii) Ground that is covered with thick foliage or high grass. Remove it
by burning or cutting down.
After every hour of operation stop the engine (turn the ignition key to
‘OFF’ position) and remove the spark plug cap. Check engine oil level
(recommended oil SAE 10w/40).
Remove all foreign matter from the digging knives assembly e.g.
wire, string, grass etc.
Replace the spark plug cap.
Do not turn the machine on its side for cleaning.
When the machine is not in use always leave the clutch lever pulled in
and secured with locking clip.
For engine maintenance please refer to engine manufacturers
manual.
Check the oil level in the gearbox by removing the plug on top of the
housing and ensure the level is within 1½” of the hole. If necessary,
top up with EP90 gear oil.
S A F E T Y
TO START ENGINE
ALWAYS start the engine in the open air
DO NOT smoke when refuelling
DO NOT mix OIL with the fuel
ALWAYS stop the engine before making any adjustments,
refuelling, moving or cleaning, or when the unit is
unattended
USE ONLY diesel from fuel containers designed for this purpose
- refuel outdoors only and replace the tank cap securely
DO NOT remove any safety guards that are fitted
DO NOT touch any moving parts or attempt any maintenance
whilst the machine is running - KEEP HANDS AND FEET
AWAY
BEFORE starting work clear the work area of any objects that
could damage the machine
DO NOT allow children or anyone uninstructed to operate the
machine - KEEP ANIMALS AWAY
o
DO NOT use on slopes or banks of more than 20
ALWAYS wear suitable clothing to give personal protection
including footwear that offers a good grip
AVOID wearing loose garments that may catch in moving parts
KNOW how to stop the machine in an emergency
NEVER interfere with any control settings on the engine
NEVER select reverse gear with your back to a wall or other
immovable object
IF A FAULT develops DO NOT attempt any repair - immediately
contact the supplier from whom the machine was obtained
VISUALLY INSPECT the machine before use - ensure all tines,
nuts and bolts are tight and not worn or damaged and
replace tines if necessary
KEEP IN MIND the operator is responsible for accidents or
hazards occurring to people or property
Using the dipstick provided, check the engine oil level. Top up with
10w/40 oil if necessary (if the dipstick is clear of oil).
Check fuel level. Only use diesel from a clean container. Never re-
fuel when the engine is hot or running. Leave 1” air space in the fuel
tank.
Depress the engine stop lever (the red lever on the left handlebar)
then pull up the clutch lever and secure with locking clip.
Ensure the wheel speed lever is in neutral ‘O’ position.
Apply half throttle (the lever on the right handlebar).
Turn the ignition key fully clockwise to start the engine then release
the key and allow it to return to the ‘RUN’ position.
When the engine has started return the throttle lever to idle position.
OPERATION
Use handlebar adjuster to set handlebar height.
Engage clutch lever (located on left handlebar). This will
automatically release stop lever locking clip.
Select forward motion lever and ensure it is in position ‘F’.
Select working speed one.
NEVER
select a higher wheel speed for
work.
Engage drive to the digging knives by pushing the lever forward, this
will give slow rotation whilst pulling the lever back gives fast rotation.
Release clutch lever slowly and
fully
,
keeping the
red engine stop
lever depressed as engine will st
o
p if released.
Commence work.
