background image

Power

Input

Output

Stitch patterns

Stitch length

7.2 watts

100-240V~50/60Hz

DC 6V 1200mA / 4 AA batteries

12

2mm

Max sewing speed

330 SPM (stitches/min.)

Max thickness

2.5mm

SPECIFICATIONS

• 

This machine is not a toy; it is not meant to be used by or near children. 

• 

Never leave machine unattended while plugged in. Turn off and unplug when not in use. 

• 

Keep machine away from direct sunlight and other sources of heat (stove, heater, etc.).

• 

Do not run power cord over sharp edges/corners or a hot surface.

• 

Do not close a door on the power cord as it could damage the cord.  

• 

Do not open the main motor case of the machine. The mechanism has been factory adjusted. 

• 

Do not submerge the unit or power cord in water or any other liquid.

• 

Do not operate machine with wet hands, without shoes, or while standing in water or on a wet surface. 

• 

Do not touch the plug with wet hands.

• 

Always check the threading of the lockstitch before sewing a seam. Improper threading or placement of

the bobbin will damage the machine.

• 

Gently guide the fabric as you sew. Do not pull fabric when sewing as it could break the needle and

damage the machine.

• 

Do not sew clothing as it is being worn. 

• 

Do not unplug the appliance by pulling on the power cord. Always grasp the plug firmly and pull

straight out from the outlet.

• 

Do not touch needle or thread machine while unit has power.  

• 

Unplug or remove power supply (including batteries) when changing needle or threading machine. 

• 

Remove batteries before storage or if machine is unused for a long period of time. 

WARNING

 Please read instructions carefully before installing or operating machine.

 Make sure to inspect the machine periodically to ensure it is in good condition.

 This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or 

lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by 

a person responsible for their safety.

 If any parts are missing, broken, damaged, or worn, stop using this item until repairs are made and/or factory replacement 

parts are installed.

 Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the product warranty.

Please retain these instructions for future reference.

NOTICE

Содержание SKY6263

























Отзывы: