BCM QS440BXP Скачать руководство пользователя страница 45

Страница: 45 / 60

Award BIOS Setup Program

3-5 PNP/PCI Configuration

This section provides IRQ and DMA setting information. By choosing the PNP/PCI

Configuration option from the CMOS Setup Utility menu (Figure 3-1), the screen below

is displayed. This sample screen contains the manufacturer's default values for the
mainboard.

ROM PCI / ISA BIOS (jm69KC0C)

PNP/PCI CONFIGURATION

AWARD SOFTWARE, INC.

:Select Item

PU/PD/+/-

: Modify

(Shift) F2

: Color

ESC : Quit

: Help

F5 : Old Values

F7 : Load Setup Defaults

PNP OS Installed

: No

Resources Controlled By: Manual

Reset Configuration Data

: Disabled

IRQ-3 assigned to

: PCI/ISA PnP

IRQ-4 assigned to

: PCI/ISA PnP

IRQ-5 assigned to

: PCI/ISA PnP

IRQ-7 assigned to

: PCI/ISA PnP

IRQ-9 assigned to

: PCI/ISA PnP

IRQ-10 assigned to

: PCI/ISA PnP

IRQ-11 assigned to

: PCI/ISA PnP

IRQ-12 assigned to

: PCI/ISA PnP

IRQ-14 assigned to

: PCI/ISA PnP

IRQ-15 assigned to

: PCI/ISA PnP

DMA-0 assigned to

: PCI/ISA PnP

DMA-1 assigned to

: PCI/ISA PnP

DMA-3 assigned to

: PCI/ISA PnP

DMA-5 assigned to

: PCI/ISA PnP

DMA-6 assigned to

: PCI/ISA PnP

DMA-7 assigned to

: PCI/ISA PnP

Figure 3-6 PCI & ONBOARD I/O Setup Screen

A. PNP OS Installed

If you want to install a PNP compatible OS (such as Windows 95) set to

Yes.

B. Resources Controlled By

When set to Manual the system BIOS will not refer to the ESCD for IRQ & DMA

information. Instead, it will refer to the items in the setup menu for assigning IRQ

& DMA. When set to Auto the system BIOS will refer to the ESCD for all legacy

information.

ESCD(Extended System Configuration Data) provides a detailed format of

the configuration data structures stored in flash memory. Each data structure

defines the resources used by a device or a card in the system. This includes

legacy and PCI/ISA PnP devices.

Slot 1&5 Use IRQ No. : Auto

Slot 2 Use IRQ No. : Auto

Slot 3 Use IRQ No. : Auto

Slot 4 Use IRQ No. : Auto

Assign IRQ For VGA

: Enabled

Assign IRQ For USB

: Enabled

Used MEM base addr

: N/A

Содержание QS440BXP





























































Результаты поиска

Содержание QS440BXP

Отзывы:

Бренды по названию

Популярные бренды

BCM QS440BXP, Руководство пользователя

Результаты поиска

Содержание QS440BXP

Отзывы:

Бренды по названию

Популярные бренды