NX530Z
NX530Z
NX530Z
Intel® Atom™ BGA Low Power Z530P, 1.6 GHz Single Core CPU with
Hyper-Threading Technology, 533 FSB
Nano ITX Motherboard
User’s Quick Start Card
Version 1.0
http://www.bcmcom.com
• Inspect the Package:
One
NX530Z Motherboard
One
Driver CD (Manual/Drivers)
One
MD6M to MD6F*2 Cable
One
44-pin IDE cable
One
COM1 Cable w/o Bracket
(9P/2.00mm)
One
ATX Power Cable
One
2-row USB Cable
One
User’s Quick Start Card
• Responsibility:
This manual is provided “As-Is” with no warranties of any kind, it will neither expressed or
implied, including, but not limited to the implied warranties or conditions of this product’s
fitness for any particular purpose. In no event shall we be liable for any loss of profits, loss of
business, loss of data, interruption of business, or indirect, special, incidental, or
consequential damages of any kind, even the possibility of such damages arising from any
defect or error in this manual or product. We reserve the right to modify and update the user
manual without prior notice.
WARNING: CMOS Battery Damage
Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium-Ion
coin cell (or equivalent) battery type to avoid risk of personal injury or physical damage to your
equipment. Always dispose of used batteries according to the manufacturer’s instructions, or
as required by the local ordinance (where applicable). The damage due to not following this
warning will void your motherboard’s manufacturer warranty.
Perchlorate Material- Special Handling May Apply.
See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
ATTENTION: Incorrect BIOS Setup
If you do not know how to handle BIOS setup or how to set it up properly, it is strongly
advisable that you do not modify any of the settings than otherwise instructed in the User’s
Quick Start Card. Even a seemingly small incorrect adjustment or modification in the BIOS
setup can render your system unstable or unusable. The incorrect BIOS setup is not covered
by your motherboard’s manufacturer warranty.
Additional Information:
Additional information on setting this board up can be found in the User’s Manual in the
provided CD-ROM. The Online User’s Manual and FAQ/Knowledge Base can be found on
our website by visiting our website:
http://www.bcmcom.com
. If your question is not
answered in our FAQ/Knowledge Base, visit our forums and post your messages or submit a
new FAQ through FAQ Submittal form for us to add your question in our FAQ with our
answer.
IDE Cable
MD6M to MD6F*2 cable
COM1 Cable
ATX Power Cable
USB Cable
WARNING: Electrostatic Sensitive Device (ESD)
Static electricity can easily damage your motherboard and will void your motherboard
warranty. Keep the motherboard and other system components in their anti-static packaging
until you are ready to install them. Touch a grounded surface before you remove any system
component from its protective anti-static packaging. Unpacking and installation should be
done on a grounded, anti-static mat. The operator should be wearing an anti-static wristband,
grounded at the same points as the anti-static mat. During configuration and installation
touch a grounded surface frequently to discharge any static electrical charge that may have
built up in your body. Avoid touching the components when handling the motherboard or a
peripheral card. Handle the motherboard and peripheral cards either by the edges or by the
peripheral card case-mounting bracket.
WARNING: Misplaced Jumper Damage
Incorrect setting jumpers and connectors may lead to damage to your motherboard and will
void your motherboard warranty. Please pay special attention not to connect these headers
in wrong directions. DO NOT change ANY jumpers while the motherboard has the power!
Connectors & Headers
• Audio Line-in (LINE_IN)
Pin Signal
1 LIN1_L
2 LIN1_R
3 LIN1_JD
4 GND
5 GND
• Serial Port (COM1)
Signal Pin Pin
Signal
DDCD# 1
2
RRXD
TTXD 3 4 DDTR#
GND 5 6 DDSR#
RRTS# 7
8
CCTS#
RRI# 9 10 [KEY]
• System Panel (F_PANEL1)
Signal Pin
Pin Signal
1 2
HD_LED- 3 4 PWR_LED-
GND 5 6
RST 7 8
PWR_BTN-
NC 9
10 [KEY]
