baxter Flo-Gard 6301 Скачать руководство пользователя страница 65

Страница: 65 / 252

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

7-19

Troubleshooting

Troubleshooting Chart

Troubleshooting Chart

Table 7-4 identifies specific failures by symptoms rather than Failure
Identification Codes.

Table 7-4

Troubleshooting Chart

Symptom

Checks

Corrective Action

Power Issues

One or both pumps cannot be turned

on.

Check backup battery voltage in

accordance with “Automatic Test

Mode 1: Calibration Mode 1” on page

9-14.
Check front panel cables for short

circuits and proper connection.
Check CN601 and CN602 for proper

connection and continuity.

Sometimes this condition is followed

by a F49 and/or F94 code. Charge or

replace the battery to clear the

condition. Repair if necessary.

One or both pumps cannot be turned

off.

Check backup battery voltage in

accordance with “Automatic Test

Mode 1: Calibration Mode 1” on page

9-14.
Check front panel cables for short

circuits.
Check CN601 and CN602 for proper

connection and continuity.
Check if all 3 LEDs are on and the

constant alarm is on.

Sometimes this condition is followed

by a F49 and/or F94 code. Recharge

or replace the battery to clear the

condition. The battery compartment

may need to be opened and the battery

momentarily disconnected to turn off

the pump.
Disconnect then reconnect lithium

battery.
Replace front panel film.
Replace CPU board.
Replace Sensor board.

Pump does not operate long on battery

power.

Verify condition and capacity of

battery.
Verify continuity of the battery

harness.

Charge the battery uninterrupted for at

least 16 hours.
Replace the battery.
Repair or replace the battery harness.

Battery does not provide rated backup

power when AC power is not

available.

Perform “Battery Check” on page

10-11.

Recharge or replace battery as

required.

Pressing a

START

key causes a

BATTERY LOW alarm.

Power the pump off and on again.

If the problem persists, recharge the

battery.
Repair as required.
If the problem persists, replace the

battery.

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 65 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: