manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 54 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 54

7

Automatic Test Modes

7-8

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

1.

Turn the pump off.

2.

Press and hold the 

CLEAR TOT VOL

 key and while pressing the numeric 

key corresponding to the automatic test mode you wish to enter (1 
through 0).

3.

While performing step 2, press the 

ON-OFF/CHARGE

 key.

4.

To exit any automatic test mode, press the 

ON-OFF/CHARGE

 key.

Automatic Test Mode 3: Manufacturing Test Mode

The initial display in this automatic mode is for a PRI RATE of 1999 mL/hr, 
PRI VTBI of 3998 mL, SEC RATE of 500 mL/hr, and SEC VTBI of 100 mL. 
Pressing the 

TIME

 key changes the primary settings as follows:

In each combination, the primary and secondary rates and VTBI can be 
manually altered.

The pump stops automatically one hour after the 

PRI START

 key was 

pressed. While the pump is running, the air sensor and the upstream and 
downstream occlusion sensors are disabled.

! WARNING !

This is an automatic test mode for testing the pump during manufacturing only. 
This mode must not be used on patients because the downstream occlusion, 
upstream occlusion and air sensors are disabled.

PRI RATE

PRI VTBI

SEC RATE

SEC VTBI

999

1998

500

100

499

998

500

100

250

500

500

100

125

250

500

100

10

20

500

100

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов