Baxi Slim 1.230 Fi страница 25 Скачать руководство пользователя

Страница: 25 / 32

11. Connection of the climatic

regulator QAA73

(accessory on demand)

Connection of the climatic regulator QAA73 to the boiler PCB must be

made through an interface card, supplied as accessory. This interface card

must be connected to A7 connector of the boiler PCB. QAA73 has to be

connected to terminals (+) and (-) of the terminal board supplied with the

regulator. It is not necessary to respect the polarity (see ﬁ gure 10)

When you install the QAA73, you must remove the room thermostat

jumper present on the power supply terminal board (terminals 1

and 2).

See the instructions enclosed with the accessories for their correct

installation and use.

Instructions given with the QAA73 also include the following

information:

• Parameters settable by the user;

• Choice of the language;

• Use of Information key.

Figure 10: Connection of the climatic regulator QAA73

REMOVE THE

JUMPER

KEY:

N.C.

Normally closed contact

Common contact

N.A.

Normally open contact

QAA73 positive pole

QAA73 negative pole

S.EXT

External probe

COLOUR OF THE WIRES:

Brown

Black

Light blue

Red

0301_1701

interface card

QAA 73

regulator

External probe

10.2. Range of operating curves

When the external probe is connected, the temperature regulation device

(knob) of the heating circuit regulates the Kt coefﬁ cient.

The pictures here below show the correspondence between the knob

position and the set curves. It is possible to set also curves between the

ones shown in the picture.

0009010500

IMPORTANT: the range of heating ﬂ ow temperature TM depends on

the position of the jumper or switch T.RISC. ( see paragraph 13). The

maximum possible temperature setting is 85 or 45 °C.

Содержание Slim 1.230 Fi

































Результаты поиска

Содержание Slim 1.230 Fi

Отзывы:

Похожие инструкции для Slim 1.230 Fi

Бренды по названию

Популярные бренды

Baxi Slim 1.230 Fi, Руководство пользователя и инсталлятора

Результаты поиска

Содержание Slim 1.230 Fi

Отзывы:

Похожие инструкции для Slim 1.230 Fi

Бренды по названию

Популярные бренды