Baxi Megaflo 2 System 12 Compact GA Скачать руководство пользователя страница 26

Страница: 26 / 26

9.0 Installation

Fig. 32

Fig. 33

9.7

Making The Electrical Connections

1. See Section 7.5 for details of the electrical supply. Undo
the securing screws and lift the case front panel off.

2. Disengage the securing tab and hinge the control box
downwards. Undo the terminal block cover securing screw
and remove the cover (Fig. 32).

3. Slacken the gland nut in the left of the boiler lower panel

and pass the mains cable through it. Remove the grommet

adjacent to the gland nut, pierce the diaphragm and insert

the cable from the external control system.

4. Leave sufficient slack in the cables to allow the Control

Box to be hinged fully open. Tighten the gland nut and refit

the grommet.

5. Connect the Earth, Permanent Live and Neutral wires to

the terminal strip.

NOTE:

Both the Permanent Live and Neutral

connections are fused.

6. Refer to the instructions supplied with the external

control(s).

IMPORTANT:

The room thermostat

MUST

be suitable

for 230V switching.

7. Remove the link between terminals 1 & 2. The switched

output from the external control must be connected to

terminal 1. (Fig. 33).

8. Replace the terminal block cover.

9.8

Preliminary Electrical Checks

1. Prior to commissioning the boiler preliminary electrical

system checks should be carried out.

2. These should be performed using a suitable meter, and

include checks for Earth Continuity,

Resistance to Earth, Short Circuit and Polarity.

Control Box

ways

fast

fuse

Fused

supp

230V

50Hz

Neutra

ue)

Earth

(green/ye

llo

(br

wn)

230V

g/y

Terminal Block

Fuses

Содержание Megaflo 2 System 12 Compact GA



























Результаты поиска

Содержание Megaflo 2 System 12 Compact GA

Отзывы:

Бренды по названию

Популярные бренды

Baxi Megaflo 2 System 12 Compact GA, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Megaflo 2 System 12 Compact GA

Отзывы:

Бренды по названию

Популярные бренды