Baur PD-TaD 80 Скачать руководство пользователя страница 20

Страница: 20 / 74

Product information

PD-TaD 80

20 / 74

822-188-3

No.

Element

Function

Anti-corona hoods of the
anti-corona protection
device

Used to protect against corona discharges

HV connection cables,
length 0.7 m and 1.2 m

Are used to connect the PD-TaD 80 to the test object

Calibrator CAL1B/CAL1E Is used to calibrate the PD test circuit

Power Box

(for standalone systems
only)

Is used for:



Power supply for the system components



Data transmission between the PD-TaD 80 and the laptop

Connection cables

Are used to connect the system components and the power supply, and for
data transmission between the system components

Further information: Chapter

Connection cables

(on page 22)

3.6.1

Calibrator

Before you can perform a partial discharge measurement, the test circuit must be calibrated
to the following parameters:



Charge (in nC)



Cable length or speed of the PD pulses.

The delivered calibrator is connected to the test object for the calibration.



For information on calibrating the PD measurement system, refer to

the user manual for the BAUR software.

Содержание PD-TaD 80











































































Результаты поиска

Содержание PD-TaD 80

Отзывы:

Baur PD-TaD 80, Руководство пользователя, Страница: 20 / 74

Результаты поиска

Содержание PD-TaD 80

Отзывы: