manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Руководство по эксплуатации, Страница: 113 / 182

Поделиться
Скачать
Baumuller BM5-O-SAF-002 Скачать руководство пользователя страница 113

Parameterization and Configuration

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

113

of 180

13

m

Single axis / double axis:

The Safety Module can be used for single and for double axes. The determination on 
the Safety Module is executed via the binary switch "Single-/double axis". 

The safe addressing of a module at a single axis is executed via the set slave address. 
In case of a double axis the following is valid for the address of the second axis:

Address Axis 2 = set Slave A 1

 

m

STO/SS1:

Provides information, if the drives at the controller in the standard configuration shall 
change in the safe status "STO" oder "SS1", when enabling the safety function. 
Information see 

Z

Chapter 13.3

– 

.

13.3 Standard Configuration

In this operating mode a safety component can be operated at the STO-inputs, in order 
to enable the safety function "STO" oder "SS1" .

NOTE!

A module, which has not been configured has a standard configuration, also. Safety 
functions can be executed here.

If a Safety Module does not have a configuration file, because it was not loaded yet or 
because before an existing configuration tool ProSafePara was deleted, then the basic 
behavior of the Safety Module is determined via the two binary switches „STO/SS1“ and 
the STO-inputs, after it was started. 

As the selected „STO/SS1“ - setting is valid for the total module, either „STO“ or „SS1“ 
can be operated. A mixed operation, where STO is executed on one axis and SS1 is 
executed on the other axis, is not implemented in the standard configuration. 

The binary switch "STO/SS1" is redundant (double) to troubleshooting. The switch 
settings influence the function of the STO-inputs of the Safety Module similarity. 

If both binary switches are set to "STO" ("off" = down-position, see 

Z

Figure 50

–

), the 

module can activate the safe status STO after starting.

If both binary switches are on "SS1" ("on" = up-position), the module can activate the safe 
status SS1 after starting. The delay time SS1 is determined in the standard configuration 
to 500 ms per default, until STO will be effective. 

The activation of the safety function is controlled by the status of the physical STO-inputs 
of the according axis (STO-input "STO_IN_1" (pin 17/35) for axis 1 and at a double axis 
additionally STO-input "STO_IN_2" (pin 2/20) for axis 2).

If the STO-input of an axis changes from High into the Low-status during operation or if 
the STO-input is not connected, which corresponds to the Low-status, the safe function, 
which was specified via the "STO/SS1"-setting is executed.

Содержание BM5-O-SAF-002























































































































































































Отзывы:

Нет отзывов