manualshive.com logo in svg

Baumer O200, Инструкция по эксплуатации

Поделиться
Скачать
Baumer O200 Скачать руководство пользователя страница 11

 

en_BA_O200_IO-Link_V1.docx 

11/34 

Baumer Electric AG 

15.08.2018/ 

 

Frauenfeld, Switzerland

 

4.3 

Configuration - Switching Signal Channel (SSC) 

The sensor features two different switching channels. Switching Signal Channel SSC1 is reserved for object 
detection. 
Switching Channel 4 includes a counter function with an auto-reset. All switching channels can be adjusted 
individually via IO-Link. All switching channels can be mapped to the MDC as well. Then they will show the 
counts detected by the channel. 
 
For more information about how to set-up the Counter/SSC4 channel and its behavior, please see section 
4.3.4. 
 

4.3.1 

Setpoints SP 

Using this parameter the user can modify the switchpoint of the sensor by enter the intensity (O200.R) or 
distance value (O200.G, O200.S) at which the sensor should switch (teach-by-value function). 

Figure 4

 

shows the illustration of the switching behavior. Regarding Single point mode only SP1 is relevant, SP2 is 
not active.  
For the Window mode SP1 & SP2 are active. The switching modes are explained in section  
Window mode is only available for the SSC1 of O200.G and for the SSC4/Counter. 
 

 

 

Figure 4 

Single Point Mode (O200.R, O200.G) 

SP1: Switch point 1 
SP2: Not active 
 

Figure 5

 Window Mode (Only O200.G or SSC4) 

SP1: Switch point 1  
SP2: Switch point 2 
 

 

 

Figure 6 

Single Point Mode (O200.S) 

SP1: Reference/backgroundposition 
 

 

 

Parameter name

 

Short Description

 

Rights

 

Unit / 
Allowed 
values

 

SSC1 Param.SP1 

Defines the value at which the related SSC is set to active (or 
inactive if inverted) or the position of the reference (O200.S) 

rw 

 

SSC1 Param.SP2  
(Only O200.G) 

Defines the value at which the related SSC is set to inactive (or 
active if inverted) 

- 

only active if SSC is set to window mode 

rw 

  

SSC1 
Param.Background 
Tolerance 

Only available for O200.S 
This value in % states the relative allowable variance of the 
reference position. (+/-) 

rw 

% 

Содержание O200



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды