Charging steps:
1. Place the watch on top of the base with
the charging pins on the back of the watch
aligned with the charging pins on the
charging dock. It will snap into position
once correctly aligned.
2. Connect the charging dock to a USB
charging adaptor (not included) or a USB
port on your computer.
RDFit App
Search for the RDFit app in
the app store to download, or
scan the QR code below for
installation.
1. Speaker
2. Touch screen
3. Side button
Disconnect from the App
For both iOS and Android devices, open
the RDFit app on your smart phone. Tap
“Device” and select “Unbinding Equipment”
to disconnect the watch from the app. You
will also need to open the Settings menu
on your smart phone. Go to Bluetooth
settings, tap on the “i” (for iOS) or “setting”
(for Android) icon on the right side of
“AFTWS0521/AFTWS0521_LE” and then tap
“Forget This Device” to finish disconnecting.
Turn On the Screen
To turn on the screen, raise your arm if you’re
wearing the watch, or press the side button.
Press the button again to turn off the screen.
Press the side button on any screen or swipe
right to exit or return to the main screen.
Raising your arm too quickly or slowly may
not turn the screen on.
Parts of the watch
First Time Use
For Android
For iOS
Applications
2
2
33
44
11
66
55
Google Play and the Google Play logo are trademarks of
Google LLC.
Apple, the Apple logo, iPhone, and iPad are trademarks of
Apple Inc., registered in the U.S. and other countries and
regions. App Store is a service mark of Apple Inc.
Turn on the Watch
Once the watch is fully charged, press and
hold the side button for 3 seconds to turn
on the watch.
To turn off the watch, press and hold the
side button for 3 seconds.
Connect to the App
Open the RDFit app on your smart phone.
On the main page, tap “Device” then
“Searching Device” and it will automatically
start to search for nearby devices. On the
device list, select “AFTWS0521_LE” to
connect to the watch. On iOS devices, you
may need to tap on “Pair” on a pop up
window.
You can also connect to the app through
the watch’s QR code. Tap the Setup icon
then “Link to app” to display the QR code
on the watch. On the RDFit app, tap “Scan
it” to scan the QR code and the watch will
connect to the app.
• Swipe right or press the side button to
return to the main screen.
• Tap on any icon to get into the sub screen.
Heart Rate
On the main menu, tap on the
>
icon
to measure your heart rate. Once connected
to the RDFit app, you can set measurement
intervals at the app (under Heart rate check).
Blood Pressure
On the main menu, tap on the
>
icon
to measure your blood pressure levels.
Blood Oxygen
On the main menu, tap on the
>
icon to
measure your blood oxygen levels.
When using the heart rate, blood pressure and
blood oxygen functions, ensure the following:
•
The smart watch has good contact with
your wrist.
•
Check that the sensor is clean and there
is no dirt or debris covering it.
•
It may take over 30 seconds before the
first result is shown on the screen.
Charge your watch before using for the
first time, you will need to charge it for
about 3 hours.
• Swipe up to get to the main menu. From
here, swipe up/down to navigate to
different menu screens.
• Swipe left for the quick access settings to
Bluetooth calls, music, pedometer, heart
rate and sleep monitor.
•
Swipe right for the notifications screen.
• Press and hold the screen for the watch
face selection page. Swipe left/right for
different options, then tap “OK” on the
screen to select.
Please allow permission and enable the
notification settings on the respective
smart phone application.
Bluetooth Calls
Swipe left to enter the Bluetooth call menu
where you can view call history, contact list
and dialer.
NOTE
: the watch will notify you to connect
to your smart phone if not connected. Your
smart phones Bluetooth must be paired to
“AFTWS0521/AFTWS0521_LE” to use the
function.
Call Operation
After your smart phone is connected to
the watch, you can directly answer/reject
incoming calls through the watch.
To answer an incoming call, swipe the icon
right. To reject the call, swipe the icon left.
1. Once fully charged, unplug the charging
dock from the charger.
4. Heart rate sensor
5. Charging pins
6. Microphone
Sports
On the main menu, tap on the
icon to
enter the multi-sport screen.
There are six activities: Out-door run, climb,
cycle, basketball, ping pong and football.
When you want to pause/stop the activity,
tap the screen once to display the pause/stop
icon. Tap the icon to pause/stop.
Tap the save icon to save the activity which
you can view later by tapping the history
icon. Tap the recycle icon to remove activity.
NOTE
: The images in this guide are for
reference only. Your watch may be a different
colour.
To keep the charging pins clean, please
use a damp cloth and gently clean the
charging pins weekly.
To enable the watch for your smart phone’s
Bluetooth calls, music playback and remote
capture, please refer to the below:
For Android devices: Go to your mobile
settings>Bluetooth. Select “Add new device”
and select “AFTWS0521/AFTWS0521_LE”
from the list. Once successfully connected,
will light up on the shortcut menu.
For iOS devices: Go to your mobile
settings>Bluetooth. Select “Add new device”
and select “AFTWS0521” from the list. Once
successfully connected,
will light up on
the shortcut menu.
NOTE
: For iOS devices, music playback and
remote capture functions will not work if you
do not pair “AFTWS0521_LE” on the pop up
screen.
Functions in any Screen
Functions On the Home Screen
• Swipe left to enter the Bluetooth music
playback menu.
• Open the music app on your smart phone.
• Tap play/pause icon to play/pause
music.
Bluetooth Music Playback
NOTE
: Your smart phones Bluetooth must be
connected to “AFTWS0521/AFTWS0521_LE”
to use the function.
• Tap previous/next icon to play the
previous/next song.
• Tap speaker icon to adjust volume level.
The smart watch will only save activity
data if the distance is more than 200
steps and 5 minutes in duration.
2
3
4
5
6
7
8
9
10
11
3.
