Bauer G 120 II V Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 138

background image

MNL-126509

April 4, 2013

Page 11

2.2.2

To Start Unit.

Press the green START Button on the Run Screen. (See Figure 2-3)

If the pressure in the system is lower than the set “Start Pressure”, the drive motor will start up powering
the compressor. If the system’s pressure is higher than the set “Start Pressure” or when the air pressure
has increased to the set “Operating Pressure”, the drive motor will automatically shutdown. The Com-
pressor will automatically restart when the system’s pressure drops below the set “Start Pressure”.

2.2.3

To Stop Unit.

Press the red STOP Button on the Run screen..

^

WARNING

Once started the compressor and drive motor will start and stop automatically.

Stay clear of all moving parts whenever unit has power.

NOTICE

In an emergency the compressor is shutdown by pressing

in the Emergency Stop Button.

«
...
19
20
21
22
23
...
»

Содержание G 120 II V











































































































































Отзывы:

Нет отзывов

Похожие инструкции для G 120 II V

Бренд: Daikin Страницы: 51

Pro A29B/50 CM3

Бренд: ABAC Страницы: 100

Freeway Freedom IRC1175

Бренд: Invacare Страницы: 24

Бренд: DeWalt Страницы: 92

Бренд: DeWalt Страницы: 100

XR FLEXVOLT LI-ION DCC1054

Бренд: DeWalt Страницы: 172

Бренд: Hitachi Страницы: 85

Бренд: Powerex Страницы: 28

Бренд: Gude Страницы: 52

Бренд: L&W Compressors Страницы: 188

Бренд: Speedaire Страницы: 48

Бренд: California Air Tools Страницы: 17

XRVS 1000 CD8 T4F HOP

Бренд: Atlas Copco Страницы: 88

Бренд: Atlas Copco Страницы: 102

Бренд: Atlas Copco Страницы: 112

M135 SIGMA CONTROL MOBIL

Бренд: KAESER Страницы: 288

Бренд: Danfoss Страницы: 20

Бренд: ProjectAir Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды