BatteryMINDer 24041 Скачать руководство пользователя страница 28

Страница: 28 / 36

Rev. H-070708

P/N VDC24041-MNL

BatteryMINDer

Model 24041

Page 28

If recharging multiple batteries, 2 or more

complete recharge cycles may be needed.

Repeat full recharge by pressing Stop/Restart but-

ton again. If still

RED

-blinking, you may need to

charge each battery separately.

Problem

Battery Condition Indicator lights

YELLOW

(After battery has been completely charged)

Solution

Battery still has an unacceptable level of sulpha-

tion and must stay connected to charger and

remain in Maintenance-Float mode (

GREEN

blink-

ing indicator) for 72 hours or longer. Then stop

charger by pressing Stop/Restart button and

observe Indicator. If still

YELLOW

repeat (up to

full cycles) or until indicator lights

GREEN

Problem

Battery Condition Indicator lights

YELLOW

(May

be several causes)

(Before battery is completely charged)

Solution

Battery can be weak due to sulphation, self dis-

charge or was very deeply discharged.

Attempt a full recharge and recheck after comple-

tion. If still

YELLOW

follow procedure for (After

battery has been completely charged.)

Problem

Charger Indicators show battery is fully charged,

but fails to provide good cranking, lighting or

equipment run time, as it did when newer.

Solution

You may have chosen too high a charge rate (2A

or 4A) for the size, capacity and / or condition of

your battery, repeat full recharge cycle at a lower

charge rate and leave in maintenance-float mode

for 72 hrs. before retesting.

Note: Slow charging in most cases, is preferable

to higher (faster) rates of charge.

Problem

Error and Charge LEDs blink simultaneously

Solution

Charger has timed out before battery has com-

pletely charged. Reset unit. Repeat reset - full

recharge by pressing Stop/Restart button and

holding it down until ALL LEDs flash. Reset

charge rate and battery type, if needed. Press

Stop/Restart button to begin full recharge.

Содержание 24041





































Результаты поиска

Содержание 24041

Отзывы:

Похожие инструкции для 24041

Бренды по названию

Популярные бренды

BatteryMINDer 24041, Инструкция по эксплуатации

Результаты поиска

Содержание 24041

Отзывы:

Похожие инструкции для 24041

Бренды по названию

Популярные бренды