Version 10/13
LED Finger Beams with LED Light Effect
Item no. 56 26 60
1. Intended use
These LED
¿
nger beams feature red, green, blue and white colors. They are perfect for any party setting. The
¿
nger beams are easily attached to your
¿
ngers and can be turned on or off individually. The LEDs light up in
different colors.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting,
¿
re, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product
names are trademarks of their respective owners. All rights reserved.
2. Delivery content
• 4
LED
¿
nger beams with LED light effect
• 12 battery cells type AG3 (installed)
• Operating
instructions
3. Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Not suitable for children under 14 years old.
ATTENTION:
The batteries are permanently built into the product and cannot be replaced.
Persons / Product
• Keep the device out of the reach of small children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
À
ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
• It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
• Attention, LED light: Do not look directly into the LED light! Do not look into the beam directly or with optical
instruments!
Batteries
• The batteries are permanently built into the product and cannot be replaced.
• Leaking or damaged batteries might cause acid burns when in contact with skin, therefore use suitable
protective gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk, that
children or pets swallow them.
• Batteries must not be dismantled, short-circuited or thrown into
¿
re. Never recharge non-rechargeable
batteries. There is a risk of explosion!
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance,
modi
¿
cations and repairs are to be performed exclusively by an expert or at a quali
¿
ed shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4. Operating elements
1
4
3
2
1 Battery compartment
2 On/off switch
3 LED
4 Rubber strap
5. Operation
1. Use the rubber strap (4) to attach a
¿
nger beam to your
¿
nger with the LED (3) pointing to the front. If
desired, attach additional
¿
nger beams to other
¿
ngers.
2. Turn on the LED light using the on/off switch (2). Do not point the LED beam at persons or animals.
3. Turn off the LED light after use using the on/off switch and remove the product from your
¿
ngers.
6. Disposal
Product
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
Remove any inserted (rechargeable) batteries and dispose of them separately from the product.
(Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/rechargeable batteries.
Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labelled with this symbol to indicate that disposal in the
domestic waste is forbidden. The designations for the heavy metals involved are: Cd = Cadmium,
Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores
or wherever (rechargeable) batteries are sold.
You thus ful
¿
l your statutory obligations and contribute to the protection of the environment.
7. Technical data
Operating voltage:
3 x 1.5 V/DC battery cells type AG3 (per each LED
¿
nger beam)
Operating time:
8-12 hours
Dimensions (W x H x D):
16 x 16 x 40 mm (per each LED
¿
nger beam)
Weight:
Approx. 21 g
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
¿
lming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also
in part, is prohibited.
The operating instructions re
À
ect the current technical speci
¿
cations at time of print.
We reserve the right to change the technical or physical speci
¿
cations.
© 2013 by Conrad Electronic SE.
V2_1013_02-HK
