background image

WALK BEHIND POWER TROWEL INSTRUCTION MANUAL 

 

WALK-BEHIND POWER TROWEL WARRANTY 

 

 

 

 

 

 

 

All products sold by Bartell Morrison Inc. and Bartell Morrison (USA) LLC (the “Company”)  are warranted 

against  defects  in  materials  and/or  workmanship;  excluding  normal  wear  on  wearing  components  and 

components covered by  a separate original  manufacturers  warranty,  for  a  period  of  24 months  from the 

date of sale to the original end user purchaser provided that certain conditions have been met. 

Conditions: 

1.  The  equipment  serial  number  has  been  registered  with  the  Company  or  its  approved  dealers, 

distributors, representatives or agents.   

2.  The equipment has been operated in an appropriate manner by qualified individuals. 

3.  The  equipment  has  been  properly  maintained  as  per  the  instructions  included  in  the  Owner’s 

Manual. 

4.  All  claims  for  warranty  must  be  filed  on  proper  forms  and  include  the  serial  number  of  the 

equipment along with proof of purchase. 

Any evidence of failure to meet these conditions may result in a denial of the warranty claim.   

 

 

 

 

 

 

Consideration of warranty claims will be at the sole discretion of the Company, or its authorized dealers, 

distributors, representatives or agents.   

The Company may, at its discretion, request that the equipment to be considered for warranty be returned 

at the owner’s expense to an authorized repair facility for inspection.  

 

 

 

 

Under  this  warranty  we  may,  at  our  discretion,  repair  or  replace  a  part  or  the  whole  of  the  defective 

component or equipment.   

 

 

 

Our Warranty coverage is limited to the cost to repair or replace the defective portion of the equipment and 

a  reasonable  (as  determined  by  the  Company)  amount  of  labour  to  conduct  the  repair  or  replacement.  

Under no circumstances shall  the Company  be  liable  for  any  additional or  exceptional costs  beyond the 

cost  to  repair  or  replace  the  defective  portion  of  the  equipment.   The  Company  shall  not  be  held 

accountable for; costs associated with travel to inspect or repair defective equipment, costs for transporting 

defective equipment to or from an authorized repair facility, costs incurred to repair or replace the defective 

equipment at any facility other than one authorized by the Company or ancillary damage caused by or as a 

result of the defective equipment.   

 

 

Under no circumstances shall equipment be returned to the Company or its authorized dealers, distributors, 

representatives  or  agents  without  the  approval  of  the  Company  as  evidenced  by  a  Returned  Goods 

Number.  To obtain a Returned Goods Number contact the factory or your authorized dealer, distributor, 

representative or agent.  

This warranty is for the sole benefit of the original end user purchaser and is not transferable to any other 

company or person.  

 

5

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201 

CREATED: 07/04 

REVISED: 05/10 

CREATED: 06/12

5

12

Содержание BM436



























Отзывы:

Похожие инструкции для BM436