Barry-Wehmiller Accraply 204RH Скачать руководство пользователя страница 33

Страница: 33 / 97

SECTION 1: SYSTEM OPERATION

1.4.4 Wipe Sensor Setup

The wipe sensor must be set up as shown below.

The leading edge of the product determines when the wipe sequence starts. This “start wipe point” must be slightly

before the gate. There is a delay in the program that will allow the product to reach the gate before the wipe starts.

The trailing edge of the product determines when the gate closes. This “gate close point” must be slightly after the

gate.

Note: the horizontal distance between the “start wipe point” and the “gate close point” should be minimized. If this

distance is too large, a second product will trigger the start wipe point before the first product clears the gate close

point and a “product-too-long” fault will occur.

WIPE

SENSOR

START

WIPE

POINT

GATE

CLOSE

POINT

WIPE

SENSOR

GATE

SETUP AND ADJUSTMENTS

Содержание Accraply 204RH


































































































Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды

Barry-Wehmiller Accraply 204RH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды