Barranca Diamond BD7CW Скачать руководство пользователя страница 6

6

    BD7CW  

 

  

 

 

 

 

 

                         SAFETY

WARNING

CALIFORNIA PROPOSITION 65 MESSAGE

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities con-

tain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive 

harm. Some examples of these chemicals are: 

 Lead, from lead-based paints 

 Crystalline silica from bricks, cement and other masonry products 

 Arsenic and chromium, from chemically treated lumber 

For further information, consult the following sources: 

http://www.osha.gov/dsg/topics/silicacrystalline/index.html 

http://www.cdc.gov/niosh/docs/96-112/ 

http://oehha.ca.gov/prop65/law/P65law72003.html 

http://www.dir.ca.gov/Title8/sub4.html 

Your risk from these exposures varies depending on how often you do this type of work. To reduce 

your exposure to these chemicals, work in a well-ventilated area, and work with approved safety 

equipment, such as dust masks that are specially designed to filter out microscopic particles. Where 

use of a dust extraction device is possible, it should be used. To achieve a high level of dust collec-

tion, use an industrial HEPA vacuum cleaner. Observe OSHA 29 CFR part 1926.57 and 1926.103.

SILICA DUST WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition 

may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, 

brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of 

airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In ad-

dition, California and some other authorities have listed respirable crystalline silica as a substance 

known to cause cancer.  When cutting such materials, always follow respiratory precautions.   

Use appropriate NIOSH-approved respiratory protection where dust hazard may occur. Paper masks 

or surgical masks without a NIOSH approval number are not recommended because they do little to 

protect the worker. For more information about respirator programs, including what respirators have 

received NIOSH approval as safe and effective, please visit the NIOSH website at: 

http://www.cdc.gov/niosh/topics/respirators

Observe OSHA regulations for respirator use (29 C.F.R.§1910.134 and §1503.1). 

Visit http://www.osha.gov for more information. 

ON

(

(

)

)

Sawing, grinding and drilling generate dust. Excessive airborne particles may cause irritation to eyes, 

skin and respiratory tract. To avoid breathing impairment, always employ dust controls and protection 

suitable to the material being sawed or drilled; See OSHA (29 CFR Part 1910.1200). 

Содержание BD7CW





























Отзывы: