manualshive.com logo in svg

Baroness LM2700, Руководство по обслуживанию

Поделиться
Скачать
Baroness LM2700 Скачать руководство пользователя страница 226

Seat

Removal of Seat

Caution

This operation should be performed by two
people since the seat is heavy.
In addition, be careful not to pinch your
fingers.

Pull up the seat handle, and then slide the
seat backward completely.

1

2

ulg8sd-004

Removal of Seat_001

1

Seat handle

2

Seat

While pulling up the seat lever, lift the seat
upward.

1

2

hsn2jo-008

Removal of Seat_002

1

Seat  lever

2

Seat

1.

2.

Follow the steps below to remove the seat.

Disconnect the seat switch wire, then
remove the wire through the seat
mounting bracket toward the seat.
Remove four bolts, and then remove the
seat.

1

5

2

4

3

ulg8sd-005

Removal of Seat_003

1

Seat lever

2

Seat

3

Seat switch wire

4

Seat mounting bracket

5

Bolt

Installation of Seat

Caution

This operation should be performed by two
people since the seat is heavy.
In addition, be careful not to pinch your
fingers.

Caution

See "Tightening torques" (Page 3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installation, reverse the removing
procedure.

Removal of Seat Mounting Bracket

Remove the seat. (See "Removal of Seat"
(Page 7-32) .)

3.

[1]

[2]

1.

LM2700

Main body

Page 7-32

Removal and installation of each section

Содержание LM2700






































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды