background image

3

USER GUIDE

Congratulations on your purchase of a Barnes 
grinder pump system. With proper care and by 
following a few simple guidelines your grinder 
pump will give you many years of dependable 
service.

Use and Care

The grinder pump station is designed to 
handle routine, domestic sewage. Solid waste 
materials should be thrown in the trash. While 
your station is capable of accepting and 
pumping a wide range of materials, regulatory 
agencies advise that the following items should 
not be introduced into any sewer either directly 
or through a kitchen waste disposal:

• Glass
• Metal
• Diapers
• Socks, rags or cloth
• Plastic objects (e.g., toys, utensils, etc.)
• Sanitary napkins or tampons

In addition you must 

NEVER

 introduce into any 

sewer:

• Explosives
• Flammable Material
• Lubricating Oil and/or Grease
• Strong Chemicals
• Gasoline

General Information

Your home wastewater disposal service is 
part of a low pressure sewer system. The key 
element in this system is the Barnes grinder 
pump station. The basin collects all wastewater 
from the house. The solids in the sewage are 
then ground to a small size suitable for pumping 
in the slurry.

The grinder pump generates suf

fi

 cient pressure 

to pump this slurry from your home to the 
wastewater plant.

Power Failure

Your grinder pump cannot dispose of wastewater 
or provide an alarm signal without electrical 
power. If electrical power service is interrupted, 
keep water usage to a minimum.

Warranty

Your grinder pump is furnished with a warranty 
against defects in material or workmanship. A 
properly completed 
Start-Up/Warranty Registration form must be 
on 

fi

 le at the Barnes factory in order to activate 

your warranty. In addition your pump must be 
installed in accordance with the installation 
instructions.
If you have a claim under the provisions 
of the warranty, contact your local Barnes 

 

Distributor.
When contacting your representative for service, 
please include your station serial number, 
pump model number, and pump serial number.

For future reference, record the following 
information:

Station Serial No:

Pump Model No:

Pump Serial No:

Local Distributor:

Distributor Telephone:

Professional Plumbing

Содержание PGPH Series

















Отзывы: