background image

Caution:  Before removing the terminal box cover and before any removal/dismantling  of the pump, make 

sure that the power supply has been switched off.

18

Fault Finding & Solution Chart

FAULT

CAUSE

SOLUTION

REMARKS

a) Power supply failure.

a)Check power supply.

b) Fuses are blown.

b) Replace fuses.

c) Motor is overloaded.

c) Check system.

d) Main contacts of starter are 
not connected well or the coil 
is defective.

d) Replace motor starter.

e) Control circuit is defective. e) Check control circuit.
f) Motor is defective.

f) Repair.

a) Fuses are blown.

a) Replace fuses.

b) Contacts of overload device

 

are faulty.

b) Check motor starter.

c) Cable connection is loose 
or faulty.

c) Check cables and power 
supply.

d) Motor winding is defective. d) Replace motor.

e) Pump mechanicably 
blocked.

e) Check and repair pump.

a)The setting of overboad is 
too low.

a) Reset overload setting.

b) Periodic power supply 
faults.

b) Check power supply.

c) Low voltage at peak times. c) Add regulator.
a) Contacts of starter are not 
contacted welI or the coil is 
faulty.

a) Change motor starter.

b) Control circuit are 
defective

b) Check control circuit.

a) Suction pipe is too small.

a) Enlarge inlet pipeline.

b) There is not sufficient water

 

in pump water inlet.

b) Improve system and 
increase coming water.

c) Liquid Ievel is Iow.

c) Try to lift liquid level.

d) Pump inlet pressure is too 
low compared with water 
temperature, pipeline Ioss 
and flow.

d) Improve system and try to 
increase the inlet pressure.

e) Suction pipe is partly 
blocked by impurities.

e) Check and clear impurities.

In the case of d) and e), 
users shall not 
disassemble the pump 
by themselves.

Motor does not run 
when started.

Overload device of 
motor starter trips out

 

immediately when 
power supply is 
switched on.

Overload device trips 
out occasionally.

Motor starter has not 
tripped out but the 
pump does not run.

Pumped water does 
not flow constantly.

Table 5

barmesapumps.com

Содержание 70120001























Отзывы: