background image

Anchoring the pavilion

BAR LOW  T Y R IE

                                                        

                                

        

quality since 1920

www.teak.com

   

 

 

 

 

 

 

 

                             Page 10 of 16

              

 

8

Make sure the structure is well aligned and levelled with the floor 

as shown in the diagram below. Consult the section below for 

recommendations on the type of anchorage required for fixing 

the structure on the floor.

level

Ground Fixing

WOOD

OPTION A

WOOD DECK/FLOOR

Requirements:

8 (2 per plates) of each

- 5/16" x 2" wood screws

- 5/16" washers 

CONCRETE

SOIL

OPTION B

CONCRETE/CEMENT FLOOR

The Permo Lock anchoring system is the recommended 
method that offers a strong permanent solution for 
anchoring your shelter and to protect it against the 
wind. See next page for instructions on how to install this 
anchor

C1

C2

C3

Remaining holes in 

plate 

(AL005)

 are used 

for fixing the structure 

on the floor

W

L

D

Distances W, L, and D are calculated 

from centre to centre of plates 

(AL005)

 

Requirements:

8 (2 per plate) of each

- 3/8” x 1

1/2

” expansion anchor

* use 1/2” cement drillm bit

Dimensions                inches (cm)

W                            111 (282)
L                              138 (350)
D                             177 (450)
C1 

 

 79 (200)

C2 

 

114 (290)

C3 

 

144 (366)

Содержание 9111210

















Отзывы: