Control Panel Operation
Operating Instructions
• Note:
Water reservoir and pipeline should be cleaned before use.
• Step 1.
Unplug the unit, and clean the water reservoir by adding water, then remove the plug to drain out the water from water reservoir.
• Step 2.
Reinstall the plastic plug, and add clean water. After connecting the power supply, press and hold “
SELECT
” button for 3 seconds to
activate pipeline self-cleaning process. After cleaning, drain out the water.
• Step 3.
Open the lid and take out the ice basket to add appropriate water into water reservoir.
• Note:
The water poured into water reservoir should be lower than the water reservoir’s
MAX
level. When water volume goes beyond the max level,
please open the bottom water drain plug to drain the spare water out. Then close the transparent lid.
• Step 4.
Select the desired ice size, the machines default size of ice is large.
• Note:
Please select the (S) small sized ice cubes when ambient temperature is below 15°C. When the ambient temperature is higher than 30°C,
(L) Large ice cube sizes are recommended.
• Note:
For the first three cycles, the ice may be small and irregular in size.
• Note:
When the ice collecting tray is full please remove the ice immediately,
DO NOT
allow the ice collecting tray to overfill.
Cleaning & Use Guidance
• 1. Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently. When cleaning, unplug the unit and remove the ice
cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Ice maker.
DO NOT
spray Ice maker with
chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
•
2. Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction.
DO NOT
use mechanical devices or other
means to accelerate the defrosting process, other than those recommended by the manufacturer.
• 3. Using the machine after being left for a period of time. It may not have enough water to pump in the system, and the indicator of “
ADD
WATER
”
will keep lighting. At this time, you just need to press
POWER
button again, the machine can enter normal state.
• 4. To ensure the cleanness of ice, please change water for water reservoir at least once one day. If not using for a long time, drain the water from
the machine, clean it and make sure it is completely dry before storing.
•
5. If the compressor stops due to a shortage of water, is over-full of water or there is an interruption of the power supply, it will delay for 3 mins to
start up after restarted.
•
6. Always use fresh water before starting ice production either at initial installation or after a long shut-off period.
• The
POWER
indicator will flash after the unit is plugged in, and then the machine enters standby state. It will start to work by
pressing
POWER
button, accompanying indicator lighting. During operation, pressing this button, the machine will return to
standby state.
• This button is for selecting the size of ice. The default setting is large ice, if the smaller one is needed, press this button. When
you select the desired size, corresponding indicator of S (small) or L (large) will be on.
• Press and hold “
SELECT
” button for 3 seconds to activate the pipeline self-clean process, which “pumps water through for 30
seconds --- water tank run to drain out water” as a cycle, and this cycle will run for 5 times. “S” and “L” will flash in turn until the
self-cleaning process is over and the machine enters standby mode. Remove the plastic plug to drain water and then whole
process will be finished.
•
When the indicator for this button turns red, it means there is insufficient water in the water reservoir, you need to add enough
water and press the
POWER
button to restart the machine.
•
When the ice reaches the max storage capacity, the indicator on this button will flash, and the machine will stop working.
Remove the ice and the machine will start again. If the level of the ice is lower than the level of ‘ice bin full’ sensor, the machine
will restart automatically.
