barfield DC400 Скачать руководство пользователя страница 31

Страница: 31 / 37

61-101-00802.EF1 Revision J

Page | 25

(14) With the INS TEST POINT switch at SIG / RTN position, verify the T/S display

shows a value between 1500 and an “over range” of 1.

Note:

Ensure conductance is within specifications. If test results are outside limits,

repeat test.

(15) Set ON / OFF switch to OFF.

(16) Disconnect Probe adapter from Probe.

(17) Disconnect Probe adapter from T/S.

D. Discrete Level Sensor Test for C90 & C90A / B /GT /GTi / GTx

(1) Connect the T/S to the probe as shown in Figure 8 and the following setps.

Figure 8

Probe Discrete Level Interface

(2) Ensure the test leads, P/N 101-01012 banana plugs are connected to the

DISCRETE LEVEL SENSOR jacks.

(3) Connect the clip ends of test leads to probe DISCRETE LEVEL SENSORS leads as

specified in the following table.

Position

Connections

Upright

Inverted

Black & Blue

Lamp OFF

Lamp ON

Black & Orange

Lamp OFF

Lamp ON

Black & White

Lamp ON

Lamp OFF

Table 13

Discrete Level Sensor Continuity for C90 & C90A / B / GT / GTi / GTx

(4) With clip ends connected to black and blue leads of sensor, hold sensor vertically.

(5) Set T/S ON / OFF switch to ON.

(6) Invert probe at each connection and verify continuity results per Table 13.

(7) Set the T/S ON / OFF switch to OFF.

Содержание DC400






































Результаты поиска

Содержание DC400

Отзывы:

Похожие инструкции для DC400

Бренды по названию

Популярные бренды

barfield DC400, Дополнение к инструкции пользователя

Результаты поиска

Содержание DC400

Отзывы:

Похожие инструкции для DC400

Бренды по названию

Популярные бренды