Bard WG3S1-A Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 59

background image

Manual 2100-483E
Page

18 of 59

12. VENT RESIZING INSTRUCTIONS

When an existing furnace is removed from a venting
system servicing other appliances, the venting system is
likely to be too large to properly vent the remaining
attached appliances.

The following steps shall be followed with each of the
appliances remaining connected to the common venting
system, placed in operation one at a time while the
other appliances remaining connected to the common
venting system are not in operation.

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel Gas
code, ANSI Z223.1 or the CAN/CGA B149
Installation Codes and these instructions. Determine
that there is no blockage or restriction, leakage,
corrosion and other deficiencies which could cause
an unsafe condition.

3. In so far as is practical, close all building doors and

windows and all doors between the space in which
the appliance(s) connected to the venting system are
located and other spaces of the building. Turn on
clothes dryers and any appliances not connected to
the venting system. Turn on any exhaust fans, such
as range hoods and bathroom exhausts, so they will
operate at maximum speed. Do not operate a
summer exhaust fan. Close fireplace dampers.

4. Follow the lighting instructions. Place the appliance

being inspected in operation. Adjust thermostat so
appliance shall operate continuously.

5. Test for draft hood equipped appliance spillage at the

draft hood relief opening after 5 minutes of main
burner operation. Use the flame of a match or
candle.

6. After it has been determined that each appliance

connected to the venting system properly vents when
tested as outlined above, return doors, windows,
exhaust fans, fireplace dampers and any other gas-
burning appliances to their previous conditions of
use.

7. If improper venting is observed during any of the

above tests, the venting system must be corrected.

13. FRESH AIR INTAKE

All units are built with fresh air inlet slots punched in
the service panel.

The default unit is built with blank-off plates installed.
All capacity, efficiency and cost of operation
information as required for Department of Energy
“Energyguide” Fact Sheets is based upon the fresh air
blank-off plate in place and is recommended for
maximum energy efficiency.

One of several other ventilation options may be
installed. Refer to model number and/or supplemental
installation instructions.

14. CONDENSATE DRAIN

A plastic drain hose extends from the drain pan at the
top of the unit down to the unit base. There are
openings in the unit base for the drain hose to pass
through. In the event the drain hose is connected to a
drain system of some type, it must be an open or vented
type system to assure proper drainage.

«
...
16
17
18
19
20
...
»

Содержание WG3S1-A




























































Отзывы:

Нет отзывов

Похожие инструкции для WG3S1-A

Бренд: Heat Controller Страницы: 36

Бренд: Bryant Страницы: 14

Бренд: Granby Страницы: 34

Бренд: Daikin Страницы: 68

Бренд: York International Страницы: 40

Бренд: Oxbox Страницы: 8

Бренд: Carrier Страницы: 18

GE APPLIANCES NF80D045S3A

Бренд: Haier Страницы: 30

Бренд: Whirlpool Страницы: 12

CARBOLITE GERO CARBOLITE GERO WA-22-30

Бренд: VERDER Страницы: 36

CARBOLITE GERO CFM 14/2 AUX

Бренд: VERDER Страницы: 44

Бренд: Yukon Eagle Страницы: 64

Бренд: Rheem Страницы: 6

Бренд: Rheem Страницы: 8

Бренд: Rheem Страницы: 8

Бренд: Rheem Страницы: 12

Prestige R96V series

Бренд: Rheem Страницы: 12

Бренд: Rheem Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды