Barco X Series, Руководство по безопасности

Страница: 4 / 10

R5906676 /01 X-series 4
Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.
The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe assembly of systems. The system must comply
with the local safety regulations regarding environmental conditions, solidity final construction, etc
…
Product care
Structural & mounting components should be kept dry, clean, lubricated (only if recommended), coated properly, and otherwise
maintained in a manner consistent with part design. Barco products must be used in a manner consistent with their design and inspected
on a routine basis for security, wear, deformation, corrosion and any other circumstances that may affect the load handling capability of
the part.
Barco recommends inspections at regular intervals for all installations and increasing in frequency for more critical installations. If a part is
found to have damage, which may cause a decrease in load capability, the part must be removed for service or replaced immediately.
Under no circumstances are Barco parts repairable by anyone other than Barco.
1.2 Important safety instructions
Instructions:
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer for further
advice should any doubts exist regarding any cleaning procedure.
• Do not block ventilation openings. Install in accordance with the manufacturers instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce
heat.
• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged then
replacement of the defective parts must be undertaken immediately.
• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus. Replace damaged power/data cords immediately.
• Only use attachments/accessories specified by the manufacturer.
• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this
apparatus when unused for long period of time.
• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, the apparatus does not operate normally, or has been dropped.
• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use caution during lifting/moving or
transporting to avoid damage by possible tipping.
• Do not use damaged LED tiles. Replace damaged parts immediately. Ensure that the spring of each locking mechanism (latch) is
functioning properly. If not, replace immediately.
1.3 Important warnings
Important warnings:
Risk of electric shock:
Do not open. To reduce the risk of electric shock, do not remove LED board from tile. No user-serviceable parts inside. Refer servicing to
qualified service personnel.
Maximum and minimum ambient temperature:
The maximum ambient temperature for the LED wall is 40°C (104°F), the minimum temperature is 0°C (32°F).
X-series tiles have an internal temperature sensor that lowers the brightness of the tile when internal temperature is too high.
The brightness will return to normal when the internal temperature has cooled sufficiently.
Low Voltage Surge Protection Device required
Due to the damaging effects of lightning, utility switching and switching electric motors of other users on the mains, this product needs to
be protected by means of a Surge Protection Device. If this product is connected to the mains through the power box from Barco this
protection device is already incorporated and no extra measures need to be taken. If this product is connected to the mains through a
power distribution box from another party, please verify that a Low Voltage Surge Protection Device according EN61643-11 or UL 1449 is
in place.
High leakage current:
The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric shock due
to high leakage current, proper grounding of the installation is required.
Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation should be
such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation must be provided.
ESD and LED's:
Safety