![background image](http://html.mh-extra.com/html/barco/x-series/x-series_installation-manual_473827039.webp)
5. Setup process of the X-series display
5.2
Set up a base stand X-series display
W
ARNING
:
The maximum height of a base stand X-series display is 10 tiles X2/X4 or 9 tiles X1.6/X1.9.
C
AUTION
:
Use cotton gloves to handle the X-series tiles.
For some applications it is not allowed that the foot beams stick out in front of the LED-wall. The illustrations
below shows the possibility to built up the X-series display at the front of the foot beams. Note that such a
con
fi
guration always requires extra ballast upon the other end of the foot beams to ensure the stability of the
whole LED-wall. Nevertheless, a lot of applications allow to build up the LED-wall in the middle of the foot
beams. This con
fi
guration requires less or no ballast upon the foot beams. Consult the “Ballast calculator”
on the secured Barco web site.
Setup process
1. The
fi
rst stage in the process is the assembly of a solid and level foot construction, which has to support the whole display. Such
a construction consists of foot beams, adjustable feet (optional) and truss/
fl
oor beams. Finally, ballast has to be placed upon the
foot beams to prevent the wall from possible tipping. Assembly of the foot construction has to be done in following sequence:
a) Installation of the adjustable feet on the foot beams. Note that this is optional. See procedure "Installing an adjustable foot
(option) on a foot beam", page 40, for detailed installation instructions.
b) Installation of the truss/
fl
oor beams upon the foot beams. See procedure "Installing X-series truss/
c) Attach the foot beams to the ground with
fi
xings and/or place the necessary ballast upon the foot beams. Ensure that the
foot beams are supported every 50 centimeters. This to prevent bending of the beam. Note that the ballast has to be placed
between the end and the last 30 cm of the foot beam. Consult the “Ballast calculator” on the secured Barco web site.
Caution:
Make sure an R-Clip is installed on both ends (left and right extremes) of the truss/
fl
oor beam assembly. In
case of multiple truss/
fl
oor beams, remove all other R-Clips at the joints between the truss/
fl
oor beams. This
is required to assure the good function of the truss/
fl
oor beam assembly.
Image 5-6
Tip:
To prevent losing unused R-Clips, clip them on the truss/
fl
oor beam cable in the vicinity of its original location.
Tip:
Place rubber mats between the foot beams of the LED wall and the smooth surface to increase friction. This will reduce
the ballast required to prevent sliding.
R5906024 X-SERIES 15/03/2016
35
Содержание X Series
