![background image](http://html.mh-extra.com/html/barco/wodan/wodan_user-manual_474394008.webp)
1. Safety
1.2
Safety training to be provided by the installer
W
ARNING
:
The installer is responsible that the user is instructed. The user will sign a document to con
fi
rm
that the instructions have been received and understood.
Users de
fi
nition
The Wodan projector is intended for persons who have been instructed and trained by a skilled person (installer or service personnel)
to identify energy sources that may cause injury and to take precautions to avoid unintentional contact with or exposure to those
energy sources.
The skilled person must instruct the user about:
•
High intensity light beam. The user must respect the exclusion zone, based on the light beam Hazard Distance (HD).
•
Dangerous energy sources inside the projector. The user is not allowed to remove any cover from the projector.
•
Small glass parts can leave the projector in the event of lamp explosion. Keep 1m (40 in) distance from the air outlet side of
the projector during operation.
•
The installation, maintenance or service is for skilled persons only.
•
The requirements for a
restricted access location
and an
exclusion zone
.
Restricted access location
To protect untrained persons and children, the projector must be installed in a
restricted access location
. The de
fi
nition of a
restricted access location
is a location for equipment where both of the following paragraphs apply:
•
Access can only be gained by skilled persons (installer or service personnel) or persons who have been instructed and trained
by a skilled person. The persons must have been instructed about the reasons for the restriction applied to the location and
about the precautions that shall be taken.
•
Access is only possible through the use of the tool or lock and key, or other means of security, and is controlled by the authority
responsible for the location.
Why a restricted access location: this is an RG3 product. Based on international requirements, no person is allowed to enter the
projected beam within the zone between the projection lens and the related Hazard Distance (HD). This shall be physically impossible
by creating suf
fi
cient separation height and width or by placing optional barriers. Within the restricted area operator training is
considered suf
fi
cient. The applicable separation heights and widths are discussed in "High Brightness precautions: Hazard Distance
Exclusion zone
The projector radiates heat on its external surfaces and from ventilation ducts during normal operation. Exposing
fl
ammable or
combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a
fi
re. For this reason, it is absolutely necessary to leave an exclusion zone around all external surfaces of the projector whereby no
fl
ammable or combustible materials are present:
•
The exclusion zone must not be less than 40 cm (16 in).
1.3
Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source. Ensure that the mains voltage and capacity matches
the projector electrical ratings (110-130V/200-240V, 15A, 50-60Hz). If you are unable to install the AC requirements, contact
your electrician. Do not defeat the purpose of the grounding.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by quali
fi
ed service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of
fi
re or electrical shock.
4
R5906102 WODAN 10/04/2018
Содержание Wodan
