5. Getting Started
3
Address key
(recessed key), to enter the address of the projector (between 0 and 9). Press the recessed
address key with a pencil, followed by pressing one digit button between 0 and 9.
4
Selection key (*)
to direct access the zoom/focus/shift functions.
5
PAUSE
to stop projection for a short time, press ’PAUSE’. The image disappears but full power is
retained for immediate restarting.
6
STBY
standby button, to start projector when the power switch is switched on and to switch off the
projector without switching off the power switch.
Attention : Switching to Standby. When the projector is running and you want to
go to standby, press the standby key for 2 seconds until the message ’Saving data,
please wait’ is displayed. Do not press any longer on the standby key otherwise
the projector will restart.
7
MUTE
not used
8
?
not used
9
Digit buttons
direct input selection.
10
Audio controls
not used
11
Picture controls
use these buttons to obtain the desired color setting.
12
Phase
used to remove the instability of the image.
13
FREEZ
press to freeze the projected image.
14
TEXT
when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale
can be removed by pressing ’TEXT’ key first. To re-display the bar scale on the screen,
press ’TEXT’ key again.
15
ENTER
to start up the adjustment mode or to confirm an adjustment or selection in the adjustment
mode.
16
Cursor keys
to make menu selections when in the adjustment mode or to zoom/focus when the direct
access is active.
Comparison between the cursor keys and the use of the ’+’ and ’-’ keys on the local keypad
: RCU = local keypad
cursor key up = ’+’ key up
cursor key down = ’-’ key down
cursor key right = ’+’ key right
cursor key left = ’-’ key left
17
EXIT
to leave the adjustment mode or to scroll upwards when in the adjustment mode.
18
RCU operation indication
lights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
Table 5-1
5.3 Operating the projector
5.3.1
Switching On
How to Switch On?
1. The Trace+ will Start Up to Standby automatically when inserting the Power Cord, the Trace+ Status Led, located on the front
side will light up red.
How to start Image Projection?
1. Press the
Standby
key on the RCU. (image 5-2)
Or,
Press a digit button to select an input source.
Tip:
Point the RCU towards the Trace+ Screen.
The Trace+ Status Led will Light Up Green and Image Projection will be started.
30
R5976781 TRACE+ 14/09/2004
Содержание Trace+ R9040341
