7. System Setup
7.14 Con
fi
guration Menu > Add Screen Destinations & Layers
General
In this procedure, you will Add Screen Destinations from the de
fi
ned outputs.
Prerequisite
•
Ensure that you are familiar with the
Con
fi
guration Menu
. For details on this menu, please refer to chapter "Con
If more than one Destination is utilized, repeat the below steps until all Destinations are added.
Add Screen Destinations
1. Click on the
Destination
tab to de
fi
ne destinations for the de
fi
ned outputs.
2. From the diagram area click on the output that you want to be part of the destination. If no connector is selected the
fi
rst available
connector will be selected.
3. Click on the
+Add Screen Destination
blue button to assign the output to the screen destination.
4. When the destination is created a box appears next to the unit diagram.
5. If there is more than one output part of the destination, for a widescreen for instance, drag and drop these outputs into the
destination box. You will observe that the destination size automatically updates as new outputs are added to the destination.
An EMP allows only a certain mix of Screen (Program) Destinations and AUX Destinations. Each card can
support up to four (4) Screen Destinations (Program Outputs), or up to four (4) AUX outputs, or two (2) AUX
and two (2) Screen Outputs. All Outputs can be AUX Destinations, and all Outputs can be assigned to Screen
Destinations. Screen Destination sizes are determined by the available amount of pixel canvas, not by the
number of Outputs assigned to a Screen Destination.
Add Layers to Destinations
Click on the
Adjust
tab that is located on the top.
1. Under the
Assign
sub-menu click on the
+Assign Layer to Destinatio
n blue button.
2. Click on this button as many times is required to add the layers you are assigning to the destination. Observe the number of
layers indicated in the Layer box is incremented every time the add button is pressed. See also "Con
3. If you need to delete layers, click on the Blue button
Delete layers
.
(Optional) Edit the Name
1. Double click on “Destination1” in the Name list to edit the name.
2. When the area turns blue, click the eraser icon to clear the
fi
eld.
3. Type a new name and hit enter when done.
(Optional) Adjust Destination Parameters
Click on the “Adjust” tab that is located on the top. In this Tab there are three sub tabs: Assign, Output and Wide (See below).
(Optional) Adjust Destination Parameters part 1 > Assign Tab
From this menu you can:
1. Edit the name.
2. Change the Destination from Screen to Aux.
3. Set the dimensions if more than one connector.
4. Use the Auto Con
fi
gure Output Format function that reads the EDID of the connected device and will produce a signal like that if
still within the rules of VESA timings.
5. Delete outputs.
6. Assign or Delete Layers.
(Optional) Adjust Destination Parameters part 2 > Output Tab
From this menu you can:
1. See the output canvas (raster) size.
236
R5905948 EVENT MASTER DEVICES 17/07/2017
Содержание S3 series
