![background image](http://html.mh-extra.com/html/barco/rlm-w6/rlm-w6_service-manual_474341006.webp)
- 6 -
Caution:
*The projection lens surface has a special coating.
1. Do not use abrasive cleaners and detergents or solvents on the
surface.
2. To prevent discoloration or fading, avoid getting cleaner on the
projector case
C). Cleaning the Main Unit
1. Clean with a soft fuzz-free cloth. In case of severe soiling, use
a well-wrung cloth dipped in a neutral agent to remove soiling
and then finish with a dry cloth.
*Do not clean with thinner, benzene or similar agents as this
could lead to deterioration or peeling of paint.
2. In case of dust in suction or exhaust holes or the interior,
disassemble the main unit and use air to remove the dust from
the inside.
D). Cleaning the filters
In order to keep the interior of the projector clean, the projector is equipped with a filter to
keep out dust and other small particles. Normally, it is recommended that you change the
projector's filter around
500 hours of projector operation at least. If you are operating the
projector in a dusty environment, it is recommended that you clean the filter more often.
When used in fog machine environment, a filter change is recommended on a regular base.
Содержание RLM W6
